Search results

Hi, we have installed 2 clusters which have some same storages defined. If i now delete eg. VM 103 on Cluster A, and have also a VM 103 on Cluster B and they have access to all storages, the storage from VM 103 on cluster B will also be deleted. Is it possible to change deletion of a vm in that...

Hi, did anyone found a solution for this?

What about this 2 years later? :-)

Hi, we have running a single proxmox cluster with 2 Ceph clusters. But its not possible to maintain ceph via GUI, so we installed the CEPH Clusters from cli ont he relevant nodes. Works good but is more work from cli :-)

Hi, thank you, i tested the echo on 2 affected hosts and the gateway is available now. I will configure it on all our hosts and will check in a few days and come back to you. Best regards, Volker

Hi, we can test to use interfaces, but a host which uses /etc/network/interfaces has the same error: cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). source...

Hi, here is the output: pveversion -v proxmox-ve: 5.4-2 (running kernel: 4.15.18-24-pve) pve-manager: 5.4-13 (running version: 5.4-13/aee6f0ec) pve-kernel-4.15: 5.4-12 pve-kernel-4.15.18-24-pve: 4.15.18-52 pve-kernel-4.15.18-11-pve: 4.15.18-34 pve-kernel-4.13.8-1-pve: 4.13.8-27 ceph...

Hi, we have a promox cluster based on Virtual Environment 5.4-13. We have some Debian clients which lose ipv6 connectivity sporadic. If we insert ip -6 addr del 2a00:d0c0:xxx::xxx/64 dev ens18 and ip -6 addr add 2a00:d0c0:xxx::xxx/64 dev ens18 the ipv6 communication is back again. Any...

Hi, with proxmox ISO 5.2-1 and UEFI mode installation works and system is usable. Best regards, Volker

At the moment i try to install with proxmox iso, looks good at the moment. Will send results later

okay, but you have to install debian on a disk not connected to the controller? I cant start installation because debian didnt find a valid controller

Hi, we have new server hardware with broadcom sas 9440-8i. Debian doesnt recognized raid controller and single drives on that controller. Has anybody allready installed debian with a 9440-8i for proxmox? Regards, Volker

Hallo, wir betreiben aktuell einen kleinen Cluster mit 8 Servern. Als Storage nutzen wir einen SSD Pool (12 OSDs), einen SAS Pool (26 OSDs) und als Backup einen NFS Speicher (Raid6). Bei den CEPH Storages haben wir insbesondere bei dem SAS Pool immer wieder Performanceprobleme und höhere IOs...

Hi, we tried new firmware from supermicro with no success. Only way we can use with Supermicro AOC-STG-i4S is Active-Passive. All other modes end up in a kernel bug. Also with another "normal" debian kernel, so its not a proxmox issue. Just for knowledge base, from our site Supermicro...

We tryed on another server with dual intel cards, here everything works as expected. We are in contact with supplier, perhaps we can get another firmware version from supermicro. At least we can change to other network cards. If we get success with this card i will report it here :-) thank you

i got it. wrong repo path. With Kernel 4.15 the same errors occurs. I think we have to change bonding type for the moment. Or any other ideas?

Hi, we have subscription for this setup now, how can we donwload/install Kernel 4.15? I dont see it in Repo. Regards, Volker

It seem it is a supermicro card with an intel chipset. All available drivers and firmwares are up2date. I am awaiting subscription for this project to test new kernel.

Hi, thank you, new driver was no success, on 1Gbit Bond on the same machine everything is fine. I will test PVE 4.15 come back to this thread with results.

Hi Support, we try to enable bonding with debian 9.3 and proxmox Virtual Environment 5.1-46. The bonding is about 2 x 10Gbit interfaces and we try to use mode 802.3ad. The lacp is active and stable as long as we shutdown one link on juniper switch for testing. When the port wents down, we...