Search results

  1. E

    Windows 16: Result verification failed

    I have made a clone of the existing Windows 2016 Proxmox VM and try to run, I am facing strange error "Boot verification Failed" I am also not able to run qm config <vmid> Kindly assist proxmox-ve: 6.2-1 (running kernel: 5.4.60-1-pve) pve-manager: 6.2-11 (running version...
  2. E

    Corosync Cluster Engine is dead. Is this normal?

    Corosync is used when you configure cluster. if there is no cluster, corosync has no relevance
  3. E

    [SOLVED] Unable to migrate VM after Removal of one of the Ring

    Problem is solved by removing entries from sshd_known_hosts and doing pvecm updatecerts -f
  4. E

    [SOLVED] Unable to migrate VM after Removal of one of the Ring

    @tom Can you please help
  5. E

    [SOLVED] Unable to migrate VM after Removal of one of the Ring

    Just an update, I am able to migrate VM from inc1pve3 to inc1pve1 but not from inc1pve1 to inc1pve3
  6. E

    [SOLVED] Unable to migrate VM after Removal of one of the Ring

    Dear All, I have two rings configured in the corosync network and I have to remove the ring configuration for one of the ring but after removal of the ringid, I am no longer able to migrate VM to each other Error as observed TASK ERROR: command '/usr/bin/ssh -e none -o...
  7. E

    No Disk visible when installing Windows in VM

    Yes this is right procedure
  8. E

    [SOLVED] Do i have to reinstall a node & ceph if i initialised it with the wrong IP-network?

    Please mark as solved
  9. E

    [SOLVED] Do i have to reinstall a node & ceph if i initialised it with the wrong IP-network?

    If the ceph cluster is already existing and keyring on new servers are same, you just change the /etc/pve/ceph.conf file with the new IP and make sure the node is reachable. Also you must be already in the proxmox cluster
  10. E

    [SOLVED] Do i have to reinstall a node & ceph if i initialised it with the wrong IP-network?

    Is it the first node??
  11. E

    Windows 10 VM only showing 1 Socket and 4 cores.

    Ok set the number of cores and reboot
  12. E

    Windows 10 VM only showing 1 Socket and 4 cores.

    Can you post the output of following 1 lscpu of the proxmox server Also in VM do the following - Click Start and search for msconfig. - Select System Configuration. - In the Boot tab, click on Advanced Options. - You should see an option to set the number of cores. Change this to the correct...
  13. E

    3 node cluster rebooted at the same time with corosync issues.

    Can you please verify the following on all the three servers pvecm status | grep -i Ring I also faced this issue that RingID is different on all the servers and all servers very gone out of sync. I could find out the reason later Just check at your end
  14. E

    [SOLVED] No GUI after a few seconds of Windows 10 start

    Tried incognito??
  15. E

    3 node cluster rebooted at the same time with corosync issues.

    Can you post output of dmesg
  16. E

    How to enable Spice with Readonly (View Rights)

    I need to enable view only mode for VM as the VM is running a monitoring display and I want user to just view the display and not click anywhere? is it possible to specify anyway in the proxmox spice-config
  17. E

    changing VM MTU to 9000

    You have to make the changes in the VM. Make sure to do the changes in network config
  18. E

    [SOLVED] Proxmox pv enterprise repo not working and subscription issue

    Go to DataCenter><Servername> >Subscription>Upload SubscriptionKey
  19. E

    [SOLVED] Ceph Node Removal Issue

    Please mark this as solved
  20. E

    [SOLVED] Ceph Node Removal Issue

    That was type ceph auth del osd-num
Top Bottom