Recent content by Ruffy91

Yes it is broken for me too. but if you toggle on and off again the "Advanced" checkbox it looks OK.

I have two upstream BGP router (with ECMP). So it is always possible for a packet to be asymmetric. But this shouldn't matter as I am not using the firewall, only thing that matters is routing table for rp_filter as I understand it. Kernel 6.2, but also same issue with the standard kernel...

I can't see a process, however there is a socket on udp/4789: root@pve01:~# ss -tulpn | grep 4789 udp UNCONN 0 0 0.0.0.0:4789 0.0.0.0:*

Can you show us the interfaces when entering ip l in the shell, are there ext1 and ext2 there?

Hi spirit, thank you for the suggestion. I checked the counter using nstat -rsz | grep IPReversePathFilter and indeed it was increasing. sysctl -w net.ipv4.conf.all.rp_filter=0 made the packets flow, default is 2 (loose source) However I don't understand yet why it does this. ip r says...

The PVE installer is a X11 application and uses xorg-server. It is probably missing a working driver for intel 13th gen integrated GPU or is incompatible with it. @COMALXD you can try the workaround presented here...

Can I use different VLANs/Subnets for EVPN and EBGP? How would such a config look. For reference: Two hosts with 10GB direct connected where I want EVPN/VXLAN on VLAN 1612/Subnet 172.16.12.0/24 On each Host two VLANs 2711 and 2712 connected via 1GBe to two upstream router on...

I added a PBR for any traffic on interface evpn01 which added a rule and route table which seem correct, but the rule is ignored by the route selection: root@chsfl1-cl01-pve01:~# ip rule 300: from all iif evpn01 lookup 10000 proto zebra 1000: from all lookup [l3mdev-table] 32765: from all...

Enjoy your holiday :) The config as generated now is: frr version 8.0.1 frr defaults datacenter hostname chsfl1-cl01-pve01 log syslog informational service integrated-vtysh-config ! ! vrf vrf_evpn vni 500 exit-vrf ! router bgp 65002 bgp router-id 100.111.64.3 no bgp default ipv4-unicast...

I try to setup the following: 3 Node Proxmox Cluster using EVPN between nodes. This works as expected. Now I want to uplink the EVPN to a Fortigate via BGP for uplink. I have added a BGP Controller to a node and set this node as exit node. Routes are correctly advertised. But traffic sent from a...

Hi Dominik. Thank you for opening the Bug report. And yes this is what I did, enter it in Bytes, sorry for not being clear.

I-m very disappointed. The new functionality is just not implemented yet. According to documentation and autocompletion in the CLI you can set the size but I can't find where it would be used in the code. It says you can define it in GByte, else it will take either 10% of the OSD size or...

When trying to add a DB to an OSD when creating the OSD via Webinterface I get the following message: "/dev/nvme0n1' is smaller than requested size '300059298201' bytes" I tried setting the db size to auto, 1 GB, 3GB or 10 GB, the number never changes. The OSD would consist of a 2TB HDD and...

Whenever I upload a file to cephfs via the web client the file gets written to the root partition instead of /mnt/pve/cephfs For big files this fills up the root partition which kills ceph-mon. How can I get the web client to upload directly to cephfs?

Hallo zusammen, Ich habe einen einzelnen host mit folgendem Storage: -2x2x4TB 2.5" in mirrored stripe -2xIntel DC S3710 400 GB mirror -8x100GB SSD in raidz1 Alle habe ich als thin storage mit Blockgrösse 4k dem cluster hinzugefügt. Alle haben ZFS mit recordsize 128k. Wenn ich eine Disk einer VM...