Hello all again.
I have an issue with my networking on my proxmox box. I did a fresh install on a new hard drive. I have 1 on-board nic with IP of 10.10.1.7, which is the IP of the proxmox box. I am able to get to box via the web interface. When I log on either via ssh or the box itself, I can ping 1 computer 10.10.1.14. I cannot ping my gateway, 10.10.1.1, nor anyother address locally nor can I ping out to internet. Tried to ping google....no joy.
interface output:
ifconfig -a
brctrl show:
Im a little fried right now. If I need to provide anything else please let me know.
*extra:
I have an additional 3 nics I would like to install into the new box. I have read that it is good practice to have each nic for a different pourpse. In my case I would like to have:
-eth0 (vmbr0) for proxmox
-eth1 (vmbr1) for virtual machines
-eth2 (vmbr2) for fault tolerance for vms
Since I cant even ping to gateway as it is now without fixing something, would this be possible after I can ping out onto the network?
I have an issue with my networking on my proxmox box. I did a fresh install on a new hard drive. I have 1 on-board nic with IP of 10.10.1.7, which is the IP of the proxmox box. I am able to get to box via the web interface. When I log on either via ssh or the box itself, I can ping 1 computer 10.10.1.14. I cannot ping my gateway, 10.10.1.1, nor anyother address locally nor can I ping out to internet. Tried to ping google....no joy.
interface output:
Code:
~# cat /etc/network/interfaces
auto lo
iface lo inet loopback
auto vmbr0
iface vmbr0 inet static
address 10.10.1.7
netmask 255.255.255.0
gateway 10.10.1.1
bridge_ports eth0
bridge_stp off
bridge_fd 0ifconfig -a
Code:
~# ifconfig -aeth0 Link encap:Ethernet HWaddr c8:60:00:6a:bb:9e
inet6 addr: fe80::ca60:ff:fe6a:bb9e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:6699 errors:0 dropped:0 overruns:0 frame:0
TX packets:3779 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:756491 (738.7 KiB) TX bytes:964652 (942.0 KiB)
Interrupt:36 Base address:0x6000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:6886 errors:0 dropped:0 overruns:0 frame:0
TX packets:6886 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1399333 (1.3 MiB) TX bytes:1399333 (1.3 MiB)
venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet6 addr: fe80::1/128 Scope:Link
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:3 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
vmbr0 Link encap:Ethernet HWaddr c8:60:00:6a:bb:9e
inet addr:10.10.1.7 Bcast:10.10.1.255 Mask:255.255.255.0
inet6 addr: fe80::ca60:ff:fe6a:bb9e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:6659 errors:0 dropped:0 overruns:0 frame:0
TX packets:3777 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:640116 (625.1 KiB) TX bytes:964316 (941.7 KiB)brctrl show:
Code:
~# brctl showbridge name bridge id STP enabled interfaces
vmbr0 8000.c860006abb9e no eth0Im a little fried right now. If I need to provide anything else please let me know.
*extra:
I have an additional 3 nics I would like to install into the new box. I have read that it is good practice to have each nic for a different pourpse. In my case I would like to have:
-eth0 (vmbr0) for proxmox
-eth1 (vmbr1) for virtual machines
-eth2 (vmbr2) for fault tolerance for vms
Since I cant even ping to gateway as it is now without fixing something, would this be possible after I can ping out onto the network?