Hi all,
This has been working for a while, however it's stopped working once I switch to domain authentication.
cifs_vms is on a truenas store also joined to the domain.
I recently recreated this smb share on freenas. This has disk images, isos, etc.
If I setup the share in Proxmox ve GUI...
Hello, and thank you for a great product!
Recently I switched from local storage to CIFS mount & used a "sync job" to sync from local disk (datastore "001") to cifs (datastore "002"). Everything worked great. All files verified on the CIFS mount. I then ran "proxmox-backup-manager datastore...
Hi all,
I've had a windows 10 vm with Quadro 2000 card passed through working perfectly on & off foro 2 weeks. Now, after rebooting it a few times the vm will no longer start. "qm start <vmid>" from the CLI gives hangs for a minute or two and then gives me:
can't deactivate LV...
Hello,I recently built a new Proxmox VE server with 3.1/2.6.32 and a seagate S600 SSD.The performance just doesn't seem very good. pveperf gives me 3k fsync/s but only 130M/s reading rate.If I do a "dd if=/dev/sda of=/dev/null bs=1M" my read rate is also 130MB.Changing nothing & booting into an...
Hello everyone,
I hope this is an easy fix. I just recently upgraded from Promox VE 1.9 to 2.2 I've also switched from a single box to a cluster configuration. When i say "upgraded" that means "back up all vms and install fresh & restore vms"
The cluster shares disks via shared LVM+DRBD...
Hello,
I recently installed Proxmox VE 2.0 on a proliant microserver in stock configuration (2G ecc ram, 250G sata disk). I've installed a single pfsense (2.0.1-RELEASE) vm and have given it two virtual nics. The nics are actually 802.1q virtual interfaces on the host. DMZ is vlan 10, lan is...
I have each of my 3 vm cluster nodes setup with balance-alb across two nics. My "gateway"/firewall (openbsd) is a guest that is bridged to one of the bonds.
eth0 + eth1 = bond0, bridge to vmbr0
However when I try to ping the guest, I get a lot of icmp redirects. Sometimes I'll get 2/3/5 in a...
Hello everyone,
I recently setup my 3rd host node and have bonded (alb) pro/100 interfaces to bridge to the wan vlan, an e1000 for the "lan" bridge, and an r8168 on the "pfsync" vlan.
After setting up bonding on the e100, if I ping the (public) ip of the GUEST from my firewall/gateway, the MAC...
Hello everyone!
I recently setup freenas with NFS & Iscsi.
For the nfs part I have 10 * 500G in a raid10. Performance is pretty good.
For the iscsi setup I have 4 * 60G OCZ agility (brand new, latest firmware) on an ibm serveraid controller. I'm using them individually right now. The...
When testing iscsi, I tried to migrate a vm & it hung.
This is a test vm with nothing important (I shut it down & made a backup before restarting it & trying the migration).
How do I kill this?
If I tell it to cancel in the webgui nothing happens. Is there a CLI command I can use to...
Hello,
I am going to be running a 4 server cluster with shared NFS filesystem (possibly on one node, possibly on a 5th node...).
I have some quite old cpu's, except for one I traded for:
Currently only "new" cpu: athlon ii x4 620
Old: be-2350, amd 4850e, amd 5050e.
Proposed new...
I tried to install/run nfs-kernel-server but when starting the server, it tells me the kernel doesn't have nfs support. Is this an oversight or on purpose? Does it break something if I use one of the kvm hosts (no openvz here) as an nfs server as well?
Edit: I'm using 2.6.32-1-pve not...
Instead of making a primary/primary setup for the entire device and place lvm on top of it, why not use LVM block devices as drbd resources?
Then you can have "primary/secondary" on a per vm basis.
Thoughts?
I haven't worked extensively with DRBD, but I had a lot of trouble figuring out how...
The machine was up, but started acting strangely a few hours later:
Mar 19 16:40:20 vm2 kernel: WARNING: at kernel/bc/net.c:334 __ub_skb_set_charge()
Mar 19 16:40:20 vm2 kernel: Pid: 4916, comm: pvemirror Not tainted 2.6.24-2-pve #1
Mar 19 16:40:20 vm2 kernel:
Mar 19 16:40:20 vm2 kernel: Call...
Do you guys have a recommendation?
I'm looking at some cheap, older B3 (TLB fixed) opterons @ 1.8ghz with 16G ram.
Would I be better with 16G ram + 8 cores @ 1.8ghz (opteron) or 16G ram on a p45 board with say a 3.0ghz quad core based on core2 architecture?
Is there a general rule of thumb?
What causes this? I moved all my vm's from vm2 to vm and then made vm master and then shut down vm2 to upgrade it from 4G to 8G ram. I then restarted it.....vm is still the master The status in the main proxmox ve page shows:
I can still migrate machines back & forth and it seems to work...
PLEASE READ THIS TUTORIAL FULLY BEFORE BEGINNING. MAKE SURE YOUR DATA IS BACKED UP TO ANOTHER MACHINE BEFORE BEGINNING! IF YOU DO NOT UNDERSTAND SOMETHING BEFORE STARTING, PLEASE POST & ASK!
I am new here but have read several threads about people wanting to use softraid. I have also read &...
Hello!
A couple of Q's. I have 2 servers (not so powerful, but they work ok) to try to create a cluster.
The name of these are "vm2" and "vm"
Configuration is as follows:
vm2: 5 * 400G raid10, 1 spare, 300G boot drive, amd athlon 5050e
vm1: 4 * 500g raid10, 1 80g boot drive, amd athlon...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.