Das ist die Prioritäts-Semantik aus den alten HA-Gruppen, die bei den Node-Affinity-Rules 1:1 übernommen wurde. strict 0 heißt nur, dass Nodes außerhalb der Rule im Notfall noch erlaubt sind. Die Zahlen innerhalb der Rule bilden trotzdem Stufen...
Yes its actually prerequisites for the upgrade to PVE9:
https://pve.proxmox.com/wiki/Upgrade_from_8_to_9#Prerequisites
Also, in general regarding the upgrade, ensure to double check the known issue in the wiki:
Roadmap Proxmox VE 8.4 known...
Hallo zusammen,
ich teste aktuellin einem 2-Node-Stretch-Cluster unter Proxmox VE 9.2.10 und habe Problem mit einer HA Node-Affinity Rule
Folgende Rule ist konfiguriert:
node-affinity: preferred-pve-clt
nodes pve-clt:100,pve-tci:50...
Nochmal:
Installiere PVE. Dort wird mit Standardeinstellungen deine komplette 4TB-Platte verwendet. Bei deinen rudimentären (CLI-)Kenntnissen und auch noch fehlender 2ten 4TB-SSD, verwende LVM und kein ZFS. PVE erledigt die interne...
powersave als Governor würd ich auf den Cluster-Nodes nochmal überdenken. Die tiefen C-States kosten Aufwach-Latenz und genau darauf reagiert Corosync empfindlich, du kriegst dann manchmal Retransmits oder Token-Timeouts obwohl netzseitig alles...
Irgendetwas würde mir dann schon einfallen was ich damit anstellen könnte. :D
Das war mir schon klar und mein PS: war auch eher als Spaß gedacht. :)
Wie gesagt habe ich hier bereits seit ein paar Jahren Realtek 10/100/1G/2.5G USB NICs im...
Der Punkt mit dem Bond stört mich bei drei Nodes am meisten: wenn beide NICs im Bond hängen, hat Corosync keinen eigenen Weg mehr. Und Corosync ist echt zickig was Jitter angeht, wenn der USB-Adapter mal kurz die Verbindung verliert (Realtek...
I won't get angry, I just think that it would still be extra information to know if that is related. I imagine most people with NFS have not set the mount option, and most people with NFS are not reporting issues.
For the original issue, it was...
Be Aware: Simply issuing a reboot inside the VM, will NOT use the current pve-qemu-kvm, so you must shutdown & then start VM again, to actually use the current pve-qemu-kvm binary.
Dann nimm halt stattdessen Indien (wovon jetzt schon mehr als 50% des von dort kommenden Traffics zu Google IPv6 ist) oder irgendein anderes Land mit mehr Internetusern als den achso verschwendeten IPv4-Bereichen des US-Militärs.
The solution is as easy: Don't use the qcow2 snapshot feature itself and just take the one of the filesystem which servers the images via nfs. Then there's no wait of minutes or hours for doing anything as all is possible in a handful of seconds.
For home lab, it's whatever you want, or need, I suppose. But with software RAID, for simpler troubleshooting and recovery from faults, I would lean towards a mirrored array for boot, rather than single parity, dual parity or even RAID10.
So...
The solution is as easy: Don't use the qcow2 snapshot feature itself and just take the one of the filesystem which servers the images via nfs. Then there's no wait of minutes or hours for doing anything as all is possible in a handful of seconds.
Hi.
I 've been missing avast for Linux for PMG 9 / debian trixie for quite some time but now I find it published on their repository server.
Took them a long time but now it's arrived
:)
Hth
If you are using a real hardware RAID controller and you want to use hardware RAID, then the RAID5 array should be configured in the RAID controller firmware first. During the Proxmox installation, that array should appear as a single logical...
RAIDz1 is terrible for VMs and drives without PLP are also no fun with ZFS. Hardware RAID5 (with battery backup for sync write caching) without ZFS is fine.
https://forum.proxmox.com/threads/fabu-can-i-use-zfs-raidz-for-my-vms.159923/ (fixed...
Und hast du dich hier mal durch das WIKI oder das Handbuch gearbeitet?
Wir geben Dir ja gerne Tipps und Hilfestellungen - aber irgendwie habe im Moment da ein Bad Feeling.....