Latest activity
-
Eetfz posted the thread Confused regarding guest isolation on cluster in Proxmox VE: Networking and Firewall.Hi, My objective is simple; I want to restrict traffic between guests on a cluster within the same subnet (VNet), while allowing explicit exceptions and upstreams traffic. I see that an isolation option exists for VNets, with the following...
-
Falk R. replied to the thread Dokumentation zum Download für Claude Proxmox Skill.OK, dann muss wohl mal einer vom Staff schreiben ob es da was gibt. -
Bbitranox replied to the thread Dokumentation zum Download für Claude Proxmox Skill.Hallo Falk, steht an sich im Post. Referenzmanual gibt es als PDF, HOWTO, TROUBLESHOOTING etc. aber nicht. Scrapen kann ich natürlich aber wenn es pdf. *.md oder ein anderes gut strukturiertes Material gibt würde ich dies dem Scrapen vorziehen.
-
MMr_Kryuchkov replied to the thread Proxmox VM Truenas Scale shows status stopped but is running.Hello, I recently encountered a similar problem. When I start the VM, the status shows "running," but after a few seconds it stops, even though the VM was running at that point. After a while, the VM becomes active again, even though it was...
-
news replied to the thread Start additional service when oci lxc container starts.i suggest, wrote your own setup from the start with ex. debian 13. -
Vvovo500 posted the thread Start additional service when oci lxc container starts in Proxmox VE: Installation and configuration.In oci images, there is no rc-service... Is there something like a Hook script which gets called at startup? How can I make sure, a certain command is started in case of container start? Example use case: A container based on a docker images...
-
BBikersmurf replied to the thread VM connection issues after subnet change. What am I missing? Real time problem..Thanks for your reply. I’ll post up once I’m back on the computer. All the VMs are affected. There’s no access between them and RDP won’t accept credentials for connections between them, Once outside the node, suddenly no problems. Connecting...
-
news reacted to networkguy3's post in the thread Storage configuration for consumer SSDs (ZFS vs LVM) with
Like.
ZFS does not work/play well with RAID controllers. To use ZFS, you should have a disk controller in HBA mode Proxmox in general does not work and play well with consumer SSDs. The boot drives get a surprising amount of traffic. It is... -
JYou have pools with different names. (( And this prevents replication which is really annoying :-( )) Migration of running VMs allows me to select a specific storage on the target Migration of LXC does not offer this to me At the end...
-
Hme2: many thanks for fixing this - pve-container 6.1.0 did not work but 6.1.1 fixed the problem for me (using "mpX: ... ro=1" mounts within the lxc config here). Yet while I agree with Johannes S and hnguk that proxmox basically did fine here...
-
Oodhiambo replied to the thread [SOLVED] MINISFORUM MS-A2 (AMD Ryzen 9 9955HX) - solution, use a ZFS option and not EXT4 when setting up storage.https://www.reddit.com/r/homelab/comments/1pa5z82/advice_msa2_for_proxmox/ - this suggests that you turn OFF secure boot as well.
-
JJust because a vendor does it, doesn’t mean it’s a good idea. Vendors sell some shady stuff and it works, most of the time. Most VMware clusters, even relatively large ones indeed have a storage design that basically resembles DRBD, mdraid or...
-
Oodhiambo replied to the thread [SOLVED] MINISFORUM MS-A2 (AMD Ryzen 9 9955HX) - solution, use a ZFS option and not EXT4 when setting up storage.In this video - https://www.youtube.com/watch?v=y5wipLOjgT0 - he installed PVE (8.4) in the same hardware as yours. Can you perhaps get the disk out and wipe it clean - remove all partitions so that it's just a raw disk and see what will happen?
-
LL1512191 posted the thread LVM-Thin - remove whitespace from VM disk in Proxmox VE: Installation and configuration.Let's say I have a VM running on PVE, which stores some files for me. For the sake of the example, we'll say that it is 100GB of DMG files and 50GB of PDF files, on the same virtual disk located on a LVM-Thin volume. I use PVE's built in backup...
-
BBärtchen replied to the thread Proxmox 9.1.5 breaks LXC mount points?.me2: many thanks for fixing this - pve-container 6.1.0 did not work but 6.1.1 fixed the problem for me (using "mpX: ... ro=1" mounts within the lxc config here). Yet while I agree with Johannes S and hnguk that proxmox basically did fine here...
-
Pproxuser77 reacted to Falk R.'s post in the thread [SOLVED] Proxmox und VM auf einem Laufwerk? with Like.
Hab ich schon geschrieben, du musst nur beim gleichen Hersteller bleiben. Genau mit vielen Usern ist ein RaidZ immer tödlich. (mit HDDs) Wenn man einen guten HW Raid eh im Server hat oder den gebraucht günstig bekommt, kann der mit billigen...
-
Pproxuser77 replied to the thread [SOLVED] Proxmox und VM auf einem Laufwerk?.Auf jeden Fall. Alles was ich am Ende sage ist... Wenn das Ding produktiv genutzt wird, würde ich entweder HW Raid mit LVM machen oder ZFS mit IT-Mode, und dann vielleicht (vorallem bei ersterem) noch schauen, dass ich einen möglichst...
-
Bbl1mp replied to the thread PVE to PBS.Yes, I also stumbled into that, when I tried to restrict permissions for the first time. :) And it is very logical, considering that not all tokens belong to/ are managed by the root@pam user.
-
Bof course, why should it not? no need to censor rfc1918 :) Looks like a permission error. Take a look at this: https://pbs.proxmox.com/docs/ Now what tripped me up the first time setting it up, was this paragraph here: Permissions for API...
-
UdoB reacted to networkguy3's post in the thread Storage configuration for consumer SSDs (ZFS vs LVM) with Like.
ZFS does not work/play well with RAID controllers. To use ZFS, you should have a disk controller in HBA mode Proxmox in general does not work and play well with consumer SSDs. The boot drives get a surprising amount of traffic. It is...