Latest activity
-
Thanks Fireon , we will test with this one -
BBingo600 posted the thread Is proxmox affected by ths one ?? - Systemd vsock sshd - Vulnerability in Proxmox VE: Networking and Firewall.Just noticed this one on mailinglist : oss-security It refers to this one. https://www.openwall.com/lists/oss-security/2025/12/28/4 Is proxmox affected ?? How does one (easiest) tell sshd to "ignore" vsock ? Or disable this "new feature"...
-
Aaoxomoxoa posted the thread broken text in browser window in Proxmox VE: Installation and configuration.I have just installed VE, and when I open a browser window and log in, there are text strings which are broken up. In the Node pane in the center, the word "Network" appears as "Ne" where it should start, and then "twork" almost at the right edge...
-
Do some searching here or online about Proxmox/Ceph on consumer/non-PLP drives, they can make a big difference. -
UdoB replied to the thread Ceph performance seems too slow.You could have put tags like this: ...your content... around it or use the "</>" symbol in the editor's tool bar. The result is just better readable, compare (visually) with your first stanza: oot@pve2:~# ceph tell osd.1 bench {...
-
DDimmKo posted the thread Problem with public IP into VM [SOLVED] in Proxmox VE: Networking and Firewall.Hello! Sorry for my very bad English. I have VM with Ubuntu Server. I created bridge EXT1 with network card on proxmox server. In this EXT1 I don't set ip, mask and gateway. Into network card I plugged cable from switch. I throw this EXT1 to...
-
Ddrnicolas posted the thread Upgrade ging schief! zfs error: failed to iinitalize .... in Proxmox VE (Deutsch/German).Nach dem letzten Upgrade geht leider nichts mehr. Ich komme mit ach und krach lokal auf die Kommandozeile Dort sehe ichj als wesentliche Meldung: "zfs error: failed to initialize the libzfs öibrary" Ich habe nochm,als versucht ein apt update...
-
Llockmartkyushu replied to the thread Auto install through iPXE (for Proxmox v8 and v9).Thank you for your response. Unfortunately, even with these changes, I am unable to boot the Official Proxmox 8 or 9 Installer Disks. I learned that the initrd is a zstd (not a gzip), and you cannot normally pxe boot into it. I am still...
-
fstrankowski replied to the thread Proxmox cluster with all nodes in the same data center and where each node has a public IP.You can still do a GRE-Tunnel inside WG :D -
Wwolframio reacted to MennoMega's post in the thread Issues after upgrading to 6.17.4-1-pve with
Like.
Ok thx man ! That was not the issue but you helped me (sort off). The issue was some default setting in teh bios. When updating the bios the SATA/NVMe is set to "Raid ON" in stead of AHCI/NVMe. See picture. Now the systems are working again ... -
SSteveITS replied to the thread Ceph performance seems too slow.Do some searching here or online about Proxmox/Ceph on consumer/non-PLP drives, they can make a big difference.
-
Bbappleby replied to the thread e1000e eno1: Detected Hardware Unit Hang:.Thanks Everyone, I was about to pull my Optiplex 7050 apart and reseat all the Ram Chips ect. I believe this occurred around the change from Promox 8 to 9. Has had me stumped for a while, so I have tried the above and will post how it goes...
-
JJonSnow replied to the thread updated to PVE 9.0 then GPU passthrough stopped working on Windows.Wanted to report I still could not get rid of error 43, even with @LongQT-sea rom or my own extracted roms on an existing 8.4 install after trying both methods. I had windows installed on another computer, so decided to take an image of it and...
-
Yyummiweb replied to the thread Backup fails when (additional) container disk is on ZFS ZVOL.Please note that the container is no longer located on the ZVOL: zfs list -ospace,type | grep "ZFS_POOL_A/zvol" ZFS_POOL_A/zvol 444G 389G 0B 96K 0B 389G filesystem...
-
Kkentravis replied to the thread Ceph performance seems too slow.The drives are nine NVMe drives each as an osd. Could it be we have the drive type set wrong somewhere? I thought we set it up a dedicated mesh network for just the cluster private network, but I see the pubic has the same ipv6 address range. The...
-
TTKitty replied to the thread Dell OpenManage installation on Proxmox 9 with Debian 13.So I just spent some time going over the script from the blog post, and looking up all of the updated packages, and testing what can be installed on Proxmox9. To expand on this, what I did was manually check the archives, and find the latest...
-
Ppringlestuffs posted the thread amdgpu-install NOT for passthrough in Proxmox VE: Installation and configuration.Hi all, I want to use OpenCL on a host system with an otherwise idle AMD iGPU. It's a Ryzen 5750GE running Proxmox VE 9.1.x. I installed amdgpu-install as per the instructions, but `amdgpu-install --usecase=dkms,opencl` blows up with a compile...
-
DDemonChicken1111 posted the thread [SOLVED] Cannot remove old kernels, Causes update/upgrade errors in Proxmox VE: Installation and configuration.Hi! I've been trying to update and upgrade my proxmox installation, however I keep getting an error related to an EFI partition being full. @homelab:/# apt-get install intel-microcode Reading package lists... Done Building dependency tree...
-
Ffirth replied to the thread Secure Boot – Microsoft UEFI CA 2023 Certificate Not Included in EFI Disk.It's not working for me for Windows Server: root@br-kvm-1:~# qm enroll-efi-keys 99165 skipping - OS type is neither Windows 10 nor Windows 11
-
Llouie1961 replied to the thread [SOLVED] Overly high SSD failure rate?.SMART report on that drive looks fine. I have seen these kind of error result from faulty SATA cables. Try replacing your sata cables before you ditch the drives. You may have to wipe the offending drives and start fresh, but that's no big deal.