Latest activity
-
SSteveITS replied to the thread [SOLVED] Loss of network when install in TP-Link TX201.I would think you'd need to run it a second time to pin the new NIC, after it's installed? I haven't gotten that far, haven't actually added any NICs to Proxmox... There are command line options to do it only on certain NICs, I see.
-
JJungle153 replied to the thread [SOLVED] Loss of network when install in TP-Link TX201.Thank you, that looks like a possible solution. I'll give it a try in the morning. Fingers crossed it does the job.
-
news replied to the thread [SOLVED] Loss of network when install in TP-Link TX201.Your network Interface names will be change, when you at another PCI Express device. you must check, if you have the right driver for your TX 201. Please see: https://www.tp-link.com/us/support/faq/3435/ -
news reacted to suschmania's post in the thread Strom sparen - tiefe C-States nur ohne aktive VMs with
Like.
Hallo zusammen, ich habe jetzt testweise auch openmediavault als VM eingerichtet, auch hier gehen die C States wie gewünscht auf C6 herunter. Es muss also an der xpenology (vm) liegen. -
SSteveITS replied to the thread [SOLVED] Loss of network when install in TP-Link TX201.Proxmox added a NIC name pinning tool in v8 that links the names nic0/1/2/3/etc. to the MAC address of the card, so the names don't change if you add cards or upgrade kernels. It will change once but then should never change again...
-
Ssuschmania replied to the thread Strom sparen - tiefe C-States nur ohne aktive VMs.Hallo zusammen, ich habe jetzt testweise auch openmediavault als VM eingerichtet, auch hier gehen die C States wie gewünscht auf C6 herunter. Es muss also an der xpenology (vm) liegen.
-
-
SSteveITS reacted to 80HD-0's post in the thread [SOLVED] Proxmox VE control panel times out when accessed over a port forward? with Like.
It was the firewall, chatbot told me both the node and datacenter needed it turned on to allow a VM to have it on, turns out only the datacenter needs it on. Chatbot stoopid, I disabled it on the node and I can connect. Will do some firewall...
-
880HD-0 reacted to SteveITS's post in the thread [SOLVED] Proxmox VE control panel times out when accessed over a port forward? with Like.
In general the packets should just need to follow the connection: PC <-> router <-> garage router <-> Proxmox Did you enable the firewall in Proxmox and maybe need to allow the remote IP?
-
880HD-0 replied to the thread [SOLVED] Proxmox VE control panel times out when accessed over a port forward?.It was the firewall, chatbot told me both the node and datacenter needed it turned on to allow a VM to have it on, turns out only the datacenter needs it on. Chatbot stoopid, I disabled it on the node and I can connect. Will do some firewall...
-
JJungle153 replied to the thread [SOLVED] Loss of network when install in TP-Link TX201.Thank you for your response. Proxmox is configured on my network and has been working perfectly with the onboard 1gb NIC. The problem only occurs when I add the new 2.5gb NIC. It takes out all conectivity, when the card is removed conectivity...
-
Jjo_strasser replied to the thread Debian 13 LXC await network timeout.I am running into the same issue with PVE 9.1.4 and Debian 12 AND 13 LXC containers. I can see approx 1k log entries / month. This should be addressed to avoid manual intervention.
-
-
JHi, I created a Debian 13 container from a template built using the Debian Appliance Builder. When installing docker.io (and on every subsequent boot), the service startup is delayed by two minutes as it waits for systemd-networkd-wait-online to...
-
Ttemplar replied to the thread proxmox 8.0.3 and 7.4-16 with smartmontools 7.2-pve3 and 7.3-pve1"program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO".Even with the last version "7.5-2~bpo13+1" from trixie backports. *sigh*
-
SSteveITS replied to the thread [SOLVED] Proxmox VE control panel times out when accessed over a port forward?.In general the packets should just need to follow the connection: PC <-> router <-> garage router <-> Proxmox Did you enable the firewall in Proxmox and maybe need to allow the remote IP?
-
880HD-0 replied to the thread [SOLVED] Proxmox VE control panel times out when accessed over a port forward?.yes, and it does work over LAN, does it need to be different for WAN access?
-
fireon reacted to Falk R.'s post in the thread [SOLVED] Machine type 'pc-q35-5.1' is deprecated with Like.
Solange man dieses Image nicht als Basis für einen Microsoft Failovercluster nutzt, empfehle ich das immer. -
fireon replied to the thread [SOLVED] Machine type 'pc-q35-5.1' is deprecated.Sehr cool, vielen Dank für diese wichtige Info. Man lernt wohl immer wieder was dazu :).
-
TTErxleben replied to the thread Win11 Festplatte: gelöschte Bereiche werden nicht freigegeben.@cwt Muss man da nicht die LVM-Thin-Kröte schlucken oder funktioniert manuelles TRIM auch bei darunterliegendem LVM? Kann ich kaum glauben, würde mich aber sehr freuen. In letzterem Fall sollte aber auch das einmalige Aktivieren der TRIM-Funktion...
-
news replied to the thread [SOLVED] Loss of network when install in TP-Link TX201.Proxmox need static IPv4, so you must Setup this IPv4 in your network.
-
UdoB reacted to Johannes S's post in the thread Can't migrate VM from shared to local storage with Like.
Yikes, is there any support available for that distro e.g. patches from the vendor? Imho using EOL software is a recipe to get hacked sooner or later
