I had sde disk fail with too many errors. i run clear label and then replace commands and it started to replace the same disk. I thout the problem is because it is USB. But during recilvering I had too many errors again. So I think it is disk. I replaced the disk and now want to start replace again but I do not understand how to run replace from here?
Code:
root@pve:~# lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS
loop0 7:0 0 8G 0 loop
sda 8:0 0 238.5G 0 disk
└─sda1 8:1 0 238.5G 0 part /mnt/SSD
sdb 8:16 0 5.5T 0 disk
├─sdb1 8:17 0 5.5T 0 part
└─sdb9 8:25 0 8M 0 part
sdc 8:32 0 5.5T 0 disk
├─sdc1 8:33 0 5.5T 0 part
└─sdc9 8:41 0 8M 0 part
sdd 8:48 0 5.5T 0 disk
├─sdd1 8:49 0 5.5T 0 part
└─sdd9 8:57 0 8M 0 part
sde 8:64 0 5.5T 0 disk
sdf 8:80 0 5.5T 0 disk
├─sdf1 8:81 0 5.5T 0 part
└─sdf9 8:89 0 8M 0 part
nvme0n1 259:0 0 953.9G 0 disk
├─nvme0n1p1 259:1 0 1007K 0 part
├─nvme0n1p2 259:2 0 1G 0 part /boot/efi
└─nvme0n1p3 259:3 0 952.9G 0 part
├─pve-swap 252:0 0 8G 0 lvm [SWAP]
├─pve-root 252:1 0 96G 0 lvm /
├─pve-data_tmeta 252:2 0 8.3G 0 lvm
│ └─pve-data-tpool 252:4 0 816.2G 0 lvm
│ ├─pve-data 252:5 0 816.2G 1 lvm
│ ├─pve-vm--123--disk--0 252:6 0 4M 0 lvm
│ ├─pve-vm--123--disk--1 252:7 0 32G 0 lvm
│ ├─pve-vm--102--disk--0 252:8 0 4M 0 lvm
│ ├─pve-vm--102--disk--1 252:9 0 240G 0 lvm
│ ├─pve-vm--102--disk--2 252:10 0 4M 0 lvm
│ ├─pve-vm--106--disk--0 252:11 0 8G 0 lvm
│ └─pve-vm--103--disk--0 252:12 0 8G 0 lvm
└─pve-data_tdata 252:3 0 816.2G 0 lvm
└─pve-data-tpool 252:4 0 816.2G 0 lvm
├─pve-data 252:5 0 816.2G 1 lvm
├─pve-vm--123--disk--0 252:6 0 4M 0 lvm
├─pve-vm--123--disk--1 252:7 0 32G 0 lvm
├─pve-vm--102--disk--0 252:8 0 4M 0 lvm
├─pve-vm--102--disk--1 252:9 0 240G 0 lvm
├─pve-vm--102--disk--2 252:10 0 4M 0 lvm
├─pve-vm--106--disk--0 252:11 0 8G 0 lvm
└─pve-vm--103--disk--0 252:12 0 8G 0 lvm
root@pve:~# zpool status -v tank
pool: tank
state: DEGRADED
status: Some supported and requested features are not enabled on the pool.
The pool can still be used, but some features are unavailable.
action: Enable all features using 'zpool upgrade'. Once this is done,
the pool may no longer be accessible by software that does not support
the features. See zpool-features(7) for details.
scan: resilvered 80.8G in 01:12:33 with 0 errors on Mon Feb 5 20:14:40 2024
config:
NAME STATE READ WRITE CKSUM
tank DEGRADED 0 0 0
raidz2-0 DEGRADED 0 0 0
sdb ONLINE 0 0 0
sdc ONLINE 0 0 0
sdd ONLINE 0 0 0
replacing-3 UNAVAIL 0 0 0 insufficient replicas
9903000246701478573 UNAVAIL 0 0 0 was /dev/sde1/old
sde REMOVED 0 0 0
sdf ONLINE 0 0 0
errors: No known data errors