USB 3.0 port not mapping host->VM

[VecH]

I use manual from wiki: http://pve.proxmox.com/wiki/USB_physical_port_mapping

# lsusb -t
/:  Bus 04.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/2p, 480M
    |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/8p, 480M
        |__ Port 3: Dev 3, If 0, Class=Human Interface Device, Driver=usbhid, 1.5M
/:  Bus 03.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/2p, 480M
    |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/6p, 480M
        |__ Port 1: Dev 7, If 0, Class=Chip/SmartCard, Driver=usbfs, 12M
        |__ Port 2: Dev 6, If 0, Class=Vendor Specific Class, Driver=usbfs, 12M
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 5000M
    |__ Port 1: Dev 6, If 0, Class=Mass Storage, Driver=usb-storage, 5000M
    |__ Port 2: Dev 7, If 0, Class=Mass Storage, Driver=usb-storage, 5000M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 480M

Need mapping:

/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 5000M
    |__ Port 1: Dev 6, If 0, Class=Mass Storage, Driver=usb-storage, 5000M
    |__ Port 2: Dev 7, If 0, Class=Mass Storage, Driver=usb-storage, 5000M

If Plug USB 2.0 device to this ports (USB3.0) available 2 new ports (4-1.7 and 4-1.8) and mapping to VM
If plug USB 3.0 device, not visible all devices in VM (visible in host), in VM no kernel messages in /var/log

# cat /etc/pve/qemu-server/100.conf|grep usb
usb0: host=4-1.7
usb1: host=4-1.8
usb2: host=2-1
usb3: host=2-2

Spoiler: usb-devices

root@host:~# usb-devices

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 2
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev=04.02
S:  Manufacturer=Linux 4.2.6-1-pve xhci-hcd
S:  Product=xHCI Host Controller
S:  SerialNumber=0000:05:00.0
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=5000 MxCh= 2
D:  Ver= 3.00 Cls=09(hub  ) Sub=00 Prot=03 MxPS= 9 #Cfgs=  1
P:  Vendor=1d6b ProdID=0003 Rev=04.02
S:  Manufacturer=Linux 4.2.6-1-pve xhci-hcd
S:  Product=xHCI Host Controller
S:  SerialNumber=0000:05:00.0
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=5000 MxCh= 0
D:  Ver= 3.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs=  1
P:  Vendor=0930 ProdID=0b1a Rev=00.01
S:  Manufacturer=TOSHIBA
S:  Product=STOR.E ALU 2S
S:  SerialNumber=201211057727
C:  #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=744mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

T:  Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 2
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev=04.02
S:  Manufacturer=Linux 4.2.6-1-pve ehci_hcd
S:  Product=EHCI Host Controller
S:  SerialNumber=0000:00:1a.0
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480 MxCh= 6
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=8087 ProdID=0020 Rev=00.00
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

T:  Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0529 ProdID=0620 Rev=01.00
S:  Manufacturer=Aladdin
S:  Product=Token JC
C:  #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=50mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=0b(scard) Sub=00 Prot=00 Driver=usbfs

T:  Bus=03 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0529 ProdID=0600 Rev=01.00
S:  Manufacturer=Aladdin Knowledge Systems Ltd.
S:  Product=Token 4.33.1.0 4.0.7
C:  #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=00 Prot=00 Driver=usbfs

T:  Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 2
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev=04.02
S:  Manufacturer=Linux 4.2.6-1-pve ehci_hcd
S:  Product=EHCI Host Controller
S:  SerialNumber=0000:00:1d.0
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480 MxCh= 8
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=8087 ProdID=0020 Rev=00.00
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

T:  Bus=04 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#=  3 Spd=1.5 MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0665 ProdID=5161 Rev=00.02
S:  Manufacturer=INNO TECH
S:  Product=USB to Serial
S:  SerialNumber=20100826
C:  #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid

How to mapping USB 3.0 port to VM (not connected devices)

 

[chacha]

same problem here and no solution yet !

 

[VecH]

I was able to connect only to specific devices (, the port could not mapping
I use VID & PID devices and add line to config VM (lsusb 0930:0b1a and 125f:312b)

# cat /etc/pve/qemu-server/100.conf | grep args
args: -device nec-usb-xhci,id=xhci,addr=0x5 -device usb-host,bus=xhci.0,vendorid=0x0930,productid=0x0b1a -device usb-host,bus=xhci.0,vendorid=0x125f,productid=0x312b

 

[VecH]

I use Wiki page https://pve.proxmox.com/wiki/USB_Devices_in_Virtual_Machines#USB3.0_2

 

[chacha]

@VecH: Thank you for the tip ! I ll try it asap. But anyway, its more like a workaround as its really annoying to have to search the device id for every device... However, it may be possible to write a short udev script to to that trick.