SMART value not showing on GUI

modem7

Member
Nov 2, 2021
35
3
13
39
When looking at SMART values on one particular SSD, I'm only getting the following:

1689374963960.png

Bash:
smartctl -i /dev/sda
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-4-pve] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org


=== START OF INFORMATION SECTION ===
Model Family:     WD Blue / Red / Green SSDs
Device Model:     WDC  WDS100T1R0A-68A4W0
Serial Number:    ****
LU WWN Device Id: 5 001b44 8b2620a9e
Firmware Version: 411010WR
User Capacity:    1,000,204,886,016 bytes [1.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
TRIM Command:     Available, deterministic, zeroed
Device is:        In smartctl database 7.3/5440
ATA Version is:   ACS-4 T13/BSR INCITS 529 revision 5
SATA Version is:  SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Fri Jul 14 23:49:56 2023 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

Bash:
smartctl -a /dev/sda
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.16-4-pve] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     WD Blue / Red / Green SSDs
Device Model:     WDC  WDS100T1R0A-68A4W0
Serial Number:    ****
LU WWN Device Id: 5 001b44 8b2620a9e
Firmware Version: 411010WR
User Capacity:    1,000,204,886,016 bytes [1.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
TRIM Command:     Available, deterministic, zeroed
Device is:        In smartctl database 7.3/5440
ATA Version is:   ACS-4 T13/BSR INCITS 529 revision 5
SATA Version is:  SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Fri Jul 14 23:51:01 2023 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (    0) seconds.
Offline data collection
capabilities:                    (0x11) SMART execute Offline immediate.
                                        No Auto Offline data collection support.
                                        Suspend Offline collection upon new
                                        command.
                                        No Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        No Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        (  10) minutes.

SMART Attributes Data Structure revision number: 4
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  5 Reallocated_Sector_Ct   0x0032   100   100   ---    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   100   100   ---    Old_age   Always       -       1227
 12 Power_Cycle_Count       0x0032   100   100   ---    Old_age   Always       -       5
165 Block_Erase_Count       0x0032   100   100   ---    Old_age   Always       -       12648572
166 Minimum_PE_Cycles_TLC   0x0032   100   100   ---    Old_age   Always       -       1
167 Max_Bad_Blocks_per_Die  0x0032   100   100   ---    Old_age   Always       -       88
168 Maximum_PE_Cycles_TLC   0x0032   100   100   ---    Old_age   Always       -       5
169 Total_Bad_Blocks        0x0032   100   100   ---    Old_age   Always       -       519
170 Grown_Bad_Blocks        0x0032   100   100   ---    Old_age   Always       -       0
171 Program_Fail_Count      0x0032   100   100   ---    Old_age   Always       -       0
172 Erase_Fail_Count        0x0032   100   100   ---    Old_age   Always       -       0
173 Average_PE_Cycles_TLC   0x0032   100   100   ---    Old_age   Always       -       1
174 Unexpected_Power_Loss   0x0032   100   100   ---    Old_age   Always       -       1
184 End-to-End_Error        0x0032   100   100   ---    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   ---    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   ---    Old_age   Always       -       0
194 Temperature_Celsius     0x0022   073   057   ---    Old_age   Always       -       27 (Min/Max 23/57)
199 UDMA_CRC_Error_Count    0x0032   100   100   ---    Old_age   Always       -       0
230 Media_Wearout_Indicator 0x0032   001   001   ---    Old_age   Always       -       0x0013000a0013
232 Available_Reservd_Space 0x0033   100   100   004    Pre-fail  Always       -       100
233 NAND_GB_Written_TLC     0x0032   100   100   ---    Old_age   Always       -       1900
234 NAND_GB_Written_SLC     0x0032   100   100   ---    Old_age   Always       -       1956
241 Host_Writes_GiB         0x0030   253   253   ---    Old_age   Offline      -       1805
242 Host_Reads_GiB          0x0030   253   253   ---    Old_age   Offline      -       4804
244 Temp_Throttle_Status    0x0032   000   100   ---    Old_age   Always       -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

Selective Self-tests/Logging not supported

Without these values, the wearout isn't being shown.

1689375267095.png
 
bump - anyone have any thoughts?

I've also tried to update the database:

Bash:
/usr/sbin/update-smart-drivedb
/var/lib/smartmontools/drivedb/drivedb.h 7.3/5533 is already up to date

Also checked that the firmware was the latest.

Looks like it's PBS that's not showing the information within the GUI.
 
Last edited:
Similar issue here. Not getting any smart values in the console.

/usr/sbin/update-smart-drivedb
updated smartctl to 7.4

This happens only for the newer SSD drives. Old one reports full set of smart values.
 

Attachments

  • Screenshot 2024-08-20 at 19.58.38.png
    Screenshot 2024-08-20 at 19.58.38.png
    60.9 KB · Views: 7