SMART error (CurrentPendingSector) detected on host

[Metz]

Ich bekomme seit ca. 10 Tagen täglich eine Warnmeldung bzgl. Smart Error.

The following warning/error was logged by the smartd daemon:
Device: /dev/sdb [SAT], 1 Currently unreadable (pending) sectors

Device info:
WDC WD30EFRX-68N32N0, S/N:WD-WCC7K5NJY8V8, WWN:5-0014ee-26483534b, FW:82.00A82, 3.00 TB

For details see host's SYSLOG.
You can also use the smartctl utility for further investigation.
The original message about this issue was sent at Mon Sep 17 18:56:21 2018 CEST Another message will be sent in 24 hours if the problem persists.​

Habe vor 10 Tagen "smartctl -t long /dev/sdb" und auch heute nochmal ausgeführt.

smartctl -l selftest /dev/sdb

smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.17-3-pve] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke

=== START OF READ SMART DATA SECTION ===
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 6117 -
# 2 Extended offline Completed without error 00% 5980 -​

smartctl -A /dev/sdb

smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.17-3-pve] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke

=== START OF READ SMART DATA SECTION ===
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 1
3 Spin_Up_Time 0x0027 181 181 021 Pre-fail Always - 5941
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 7
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 092 092 000 Old_age Always - 6118
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 7
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 69
194 Temperature_Celsius 0x0022 111 105 000 Old_age Always - 39
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 8​

Wie bekomme ich den Current Pending Sektor auf 0 gesetzt so dass ich nicht mehr täglich eine email mit der Fehlermeldung bekomme?

Danke und Gruss
Metz

 

[HBO]

Ich hatte das Gleiche mal mit einer Temperatur Schwankung auf einer Festplatte. Die Werte können nicht zurück gesetzt werden, da hilft nur die Checks anpassen bzw Platte aus dem Smart Tool nehmen.