Proxmox 9.0.11
Mainboard Supermicro H12SSL-i
Hello , I have a problem with one of the 3 SSDs in Raidz 1-0 , In the Disk I see Failed! But the state of the Pool is good . I have to worry?
3 SSD SAMSUNG PM893
Pool Status
SSD
Mainboard Supermicro H12SSL-i
Hello , I have a problem with one of the 3 SSDs in Raidz 1-0 , In the Disk I see Failed! But the state of the Pool is good . I have to worry?
3 SSD SAMSUNG PM893
Pool Status
Code:
pool: StorageMZ
state: ONLINE
scan: resilvered 1.61M in 00:00:00 with 0 errors on Mon Nov 3 10:57:47 2025
config:
NAME STATE READ WRITE CKSUM
StorageMZ ONLINE 0 0 0
raidz1-0 ONLINE 0 0 0
ata-SAMSUNG_MZ7L3960HCJR-00A07_S727NJ0WB00260K ONLINE 0 0 0
ata-SAMSUNG_MZ7L3960HCJR-00A07_S727NJ0WB00261W ONLINE 0 0 0
ata-SAMSUNG_MZ7L3960HCJR-00A07_S727NJ0WB00264B ONLINE 0 0 0SSD
Code:
smartctl 7.4 2024-10-15 r5620 [x86_64-linux-6.14.11-4-pve] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Samsung based SSDs
Device Model: SAMSUNG MZ7L3960HCJR-00A07
Serial Number: S727NJ0WB00260K
LU WWN Device Id: 5 002538 f33b2551d
Firmware Version: JXTC304Q
User Capacity: 960,197,124,096 bytes [960 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available, deterministic, zeroed
Device is: In smartctl database 7.3/5528
ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Tue Nov 4 16:54:20 2025 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 60) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 11375
12 Power_Cycle_Count 0x0032 078 078 000 Old_age Always - 21218
177 Wear_Leveling_Count 0x0013 097 097 005 Pre-fail Always - 281
179 Used_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 0
180 Unused_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 882
181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 100 100 010 Old_age Always - 0
183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
187 Uncorrectable_Error_Cnt 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0032 054 043 000 Old_age Always - 46
194 Temperature_Celsius 0x0022 054 043 000 Old_age Always - 46 (Min/Max 25/57)
195 ECC_Error_Rate 0x001a 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
199 CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0
202 Exception_Mode_Status 0x0033 001 001 010 Pre-fail Always FAILING_NOW 1507328
235 POR_Recovery_Count 0x0012 099 099 000 Old_age Always - 21166
241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 140661545203
242 Total_LBAs_Read 0x0032 099 099 000 Old_age Always - 42390163409
243 SATA_Downshift_Ct 0x0032 099 099 000 Old_age Always - 24
244 Thermal_Throttle_St 0x0032 100 100 000 Old_age Always - 1
245 Timed_Workld_Media_Wear 0x0032 100 100 000 Old_age Always - 65535
246 Timed_Workld_RdWr_Ratio 0x0032 100 100 000 Old_age Always - 65535
247 Timed_Workld_Timer 0x0032 100 100 000 Old_age Always - 65535
251 NAND_Writes 0x0032 100 100 000 Old_age Always - 507897540992
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Offline Completed without error 00% 11346 -
# 2 Extended offline Completed: unknown failure 90% 11346 0
# 3 Offline Completed without error 00% 11346 -
# 4 Short offline Completed: unknown failure 90% 11345 0
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
256 0 65535 Read_scanning was never started
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
The above only provides legacy SMART information - try 'smartctl -x' for more
