Proxmox IP/Web Interface timing out

K

KeHow

New Member
Dec 16, 2021
3
0
1
32
I am installing Proxmox VE 7.0 on two HP Proliant DL380 G5 servers and I'm trying to configure them. But every time I do a search for the IP address they give you the browser times out. I have tried pinging the address with the same result. I have also tried alternately disabling and enabling PXE and iSCSI on the two NICs. I'm very much new to Proxmox and installing OSs. What am I doing wrong here? Is there something I'm overlooking?
 
Hi,

Could you please post the output of the following commands from your Proxmox VE node
Bash: 
ip a
cat /etc/network/interfaces
 
Hi! The output I got for "ip a" is
Code: 
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: enp6s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq master vmbr0 state DOWN group default qlen 1000
    link/ether 00:23:7d:d2:35:48 brd ff:ff:ff:ff:ff:ff
3: enp8s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 00:23:7d:d2:35:4a brd ff:ff:ff:ff:ff:ff
4: ens7f0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 00:26:55:81:9c:94 brd ff:ff:ff:ff:ff:ff
    altname enp25s0f0
5: ens7f1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 00:26:55:81:9c:96 brd ff:ff:ff:ff:ff:ff
    altname enp25s0f1
6: ens6f0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 00:26:55:81:ac:1c brd ff:ff:ff:ff:ff:ff
    altname enp19s0f0
7: ens6f1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 00:26:55:81:ac:1e brd ff:ff:ff:ff:ff:ff
    altname enp19s0f1
8: vmbr0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000
    link/ether 00:23:7d:d2:35:48 brd ff:ff:ff:ff:ff:ff
    inet 192.168.100.2/24 scope global vmbr0
       valid_lft forever preferred_lft forever
and for "cat /etc/network/interfaces" the output is
Code: 
auto lo
iface lo inet loopback

iface enp6s0 inet manual

auto vmbr0
iface vmbr0 inet static
        address 192.168.100.2/24
        gateway 192.168.100.1
        bridge-ports enp6s0
        bridge-stp off
        bridge_fd 0
        
iface enp8s0 inet manual

iface ens7f0 inet manual

iface ens7f1 inet manual

iface ens6f0 inet manual

iface ens6f1 inet manual
 
I noticed that the ethernet port LED was a solid amber on both my computer and the node, which I think means that the connection maxes out at 100 Mbps. Should I get a new ethernet cable? The status shows "no Internet."
 
Last edited:
You must log in or register to reply here.
Top Bottom