Oh, Oh Glad I saw This...

[Nollimox]

Well I saw this while installing Debian 12.1 and knew I had to check it out. PCIE bridge...




02:00.0 PCI bridge: PLX Technology, Inc. PEX 8724 24-Lane, 6-Port PCI Express Gen 3 (8 GT/s) Switch, 19 x 19mm FCBGA (rev ca) (prog-if 00 [Normal decode])
Subsystem: PLX Technology, Inc. PEX 8724 24-Lane, 6-Port PCI Express Gen 3 (8 GT/s) Switch, 19 x 19mm FCBGA
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
NUMA node: 0

03:00.0 PCI bridge: PLX Technology, Inc. PEX 8724 24-Lane, 6-Port PCI Express Gen 3 (8 GT/s) Switch, 19 x 19mm FCBGA (rev ca) (prog-if 00 [Normal decode])
Subsystem: PLX Technology, Inc. PEX 8724 24-Lane, 6-Port PCI Express Gen 3 (8 GT/s) Switch, 19 x 19mm FCBGA
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 27
NUMA node: 0

b2:02.0 PCI bridge: Intel Corporation Sky Lake-E PCI Express Root Port C (rev 04) (prog-if 00 [Normal decode])
Subsystem: Dell Sky Lake-E PCI Express Root Port C
Physical Slot: 12
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 33
NUMA node: 0
Bus: primary=b2, secondary=b4, subordinate=b4, sec-latency=0

b2:03.0 PCI bridge: Intel Corporation Sky Lake-E PCI Express Root Port D (rev 04) (prog-if 00 [Normal decode])
Subsystem: Dell Sky Lake-E PCI Express Root Port D
Physical Slot: 13
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 34
NUMA node: 0
Bus: primary=b2, secondary=b5, subordinate=b5, sec-latency=0


Would you agree is best to return this Dell?

 

[Nollimox]

@ubu

Since you were familiar the the problems I had faced here: https://forum.proxmox.com/threads/does-proxmox-8-work-on-modern-computers-yes.133195/ as well as that I had Pcie power fault.

So, since the power fault is on the four PCIe bridges, it seems to suggest a failing motherboard or the Pcie part of it. Since I recently bought this hardware and have til October 1, to return it, I am thinking to do just that and get another...better to be safe than sorry.

Would you say my plan makes sense, especially after the experience in the above thread?

 

[ubu]

I REALLY cannot detect a Hardware faillure on your board remotly, sorry, chrystal Ball fell down
It was just someting that was strange in your log, it could be harmless, could be a defect

 

[ubu]

Similar problems

https://forums.servethehome.com/ind...-disabled-weird-power-failure-messages.36553/

Try if this works for you otherwise return the Board and get anotjer one

 

[Nollimox]

sorry, chrystal Ball fell down

LMAO...

 

[Nollimox]

Similar problems

https://forums.servethehome.com/ind...-disabled-weird-power-failure-messages.36553/

Try if this works for you otherwise return the Board and get anotjer one

Well, after removing all added PCIe devices except the graphics card but moving it to another slot, still got the same exact result.
So, I returned it this morning and now shopping for a replacement. Thank you...