Intel X710 does not come up after Proxmox upgrade

[Dan Craciun]

Hello,

I've upgraded this morning to 5.3-1. The 10G interface does not come up anymore.

Looks like the driver used is wrong. Any ideas? The corresponding 10G port in the switch is up.

ethtool -i eth1
driver: tg3
version: 3.137
firmware-version: 5719-v1.47
expansion-rom-version:
bus-info: 0000:06:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: no

lspci | grep Eth
06:00.0 Ethernet controller: Broadcom Limited NetXtreme BCM5719 Gigabit Ethernet PCIe (rev 01)
06:00.1 Ethernet controller: Broadcom Limited NetXtreme BCM5719 Gigabit Ethernet PCIe (rev 01)
06:00.2 Ethernet controller: Broadcom Limited NetXtreme BCM5719 Gigabit Ethernet PCIe (rev 01)
06:00.3 Ethernet controller: Broadcom Limited NetXtreme BCM5719 Gigabit Ethernet PCIe (rev 01)
09:00.0 Ethernet controller: Intel Corporation Device 37cc (rev 09)
2f:00.0 Ethernet controller: Intel Corporation Ethernet Controller X710 for 10GbE SFP+ (rev 01)
2f:00.1 Ethernet controller: Intel Corporation Ethernet Controller X710 for 10GbE SFP+ (rev 01)

pveversion -v
proxmox-ve: 5.3-1 (running kernel: 4.15.18-9-pve)
pve-manager: 5.3-5 (running version: 5.3-5/97ae681d)
pve-kernel-4.15: 5.2-12
pve-kernel-4.13: 5.2-2
pve-kernel-4.15.18-9-pve: 4.15.18-30
pve-kernel-4.13.16-4-pve: 4.13.16-51
pve-kernel-4.13.16-2-pve: 4.13.16-48
pve-kernel-4.13.16-1-pve: 4.13.16-46
pve-kernel-4.13.13-2-pve: 4.13.13-33
corosync: 2.4.4-pve1
criu: 2.11.1-1~bpo90
glusterfs-client: 3.8.8-1
ksm-control-daemon: 1.2-2
libjs-extjs: 6.0.1-2
libpve-access-control: 5.1-3
libpve-apiclient-perl: 2.0-5
libpve-common-perl: 5.0-43
libpve-guest-common-perl: 2.0-18
libpve-http-server-perl: 2.0-11
libpve-storage-perl: 5.0-33
libqb0: 1.0.3-1~bpo9
lvm2: 2.02.168-pve6
lxc-pve: 3.0.2+pve1-5
lxcfs: 3.0.2-2
novnc-pve: 1.0.0-2
proxmox-widget-toolkit: 1.0-22
pve-cluster: 5.0-31
pve-container: 2.0-31
pve-docs: 5.3-1
pve-edk2-firmware: 1.20181023-1
pve-firewall: 3.0-16
pve-firmware: 2.0-6
pve-ha-manager: 2.0-5
pve-i18n: 1.0-9
pve-libspice-server1: 0.14.1-1
pve-qemu-kvm: 2.12.1-1
pve-xtermjs: 1.0-5
qemu-server: 5.0-43
smartmontools: 6.5+svn4324-1
spiceterm: 3.0-5
vncterm: 1.5-3
zfsutils-linux: 0.7.12-pve1~bpo1

 

[Dan Craciun]

Looks like on update Proxmox/Debian renumbered the NICs.

eth1 is now named eth0 and has the correct driver

Well, that's 2 hours I'm never getting back...

 

[confused_15]

This bit me too. Don't get caught in the trap in your interfaces are showing down with 'ip link show'.