Guest Windows 2003 crash

  • Thread starter Thread starter sub3xt1
  • Start date Start date
S

sub3xt1

Guest
vhost:~# pveversion
pve-manager/1.3/4023

vhost:~# pveperf
CPU BOGOMIPS: 81070.93
REGEX/SECOND: 675575
HD SIZE: 33.22 GB (/dev/pve/root)
BUFFERED READS: 166.85 MB/sec
AVERAGE SEEK TIME: 4.30 ms
FSYNCS/SECOND: 158.60
DNS EXT: 67.73 ms
DNS INT: 0.60 ms (mydomain.com)

vhost:~# cat /etc/qemu-server/101.conf
ostype: w2k3
memory: 1024
onboot: 1
name: server.mydomain.com
ide2: win_2003_EE_SP1.iso,media=cdrom
smp: 1
vlan0: e1000=62:28:58:1B:A0:EA
bootdisk: scsi0
scsi0: vm-101-disk.qcow2

vhost:~# cat /proc/cpuinfo
.......
processor : 15
vendor_id : GenuineIntel
cpu family : 6
model : 26
model name : Intel(R) Xeon(R) CPU E5540 @ 2.53GHz
stepping : 5
cpu MHz : 2533.422
cache size : 8192 KB
physical id : 1
siblings : 8
core id : 3
cpu cores : 4
fpu : yes
fpu_exception : yes
cpuid level : 11
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp lm constant_tsc arch_perfmon pebs bts rep_good pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr dca sse4_1 sse4_2 popcnt lahf_lm
bogomips : 5066.70
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management:

>> it is 2x processor quadcore with 8 GB. <<

vhost:~# dmesg |grep Broad
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.6.9 (December 8, 2007)
eth0: Broadcom NetXtreme II BCM5709 1000Base-SX (C0) PCI Express found at mem 92000000, IRQ 30, node addr 00:21:5e:97:d5:e4
eth1: Broadcom NetXtreme II BCM5709 1000Base-SX (C0) PCI Express found at mem 94000000, IRQ 37, node addr 00:21:5e:97:d5:e6



situation:
i install fully virtuallization several times.
i read a lot of trouble windows 2003 server + KVM, so i try best my suitable here.
the configurtaion is almost same, with standart video graphic (in windows is detected as cirrus logic).

#1 install
a. network card : e1000
b. hdd type : SCSI
result : windows is unstable, slow response, BSOD after success installation, most of all: networrking is not working

#2 install - 2x
a. network card : rtl8139
b. hdd type : SCSI
result : windows is unstable, slow response, BSOD after success installation

#3 install - 2x
a. network card : rtl8139
b. hdd type : IDE
result : windows is unstable, slow response, BSOD after rebooted

is there any default configuration that works??
 
do not use scsi for windows. IDE or Virtio is stable.
 
sub3xt1 said:
vhost:~# pveversion
pve-manager/1.3/4023

vhost:~# pveperf
CPU BOGOMIPS: 81070.93
REGEX/SECOND: 675575
HD SIZE: 33.22 GB (/dev/pve/root)
BUFFERED READS: 166.85 MB/sec
AVERAGE SEEK TIME: 4.30 ms
FSYNCS/SECOND: 158.60
DNS EXT: 67.73 ms
DNS INT: 0.60 ms (mydomain.com)

vhost:~# cat /etc/qemu-server/101.conf
ostype: w2k3
memory: 1024
onboot: 1
name: server.mydomain.com
ide2: win_2003_EE_SP1.iso,media=cdrom
smp: 1
vlan0: e1000=62:28:58:1B:A0:EA
bootdisk: scsi0
scsi0: vm-101-disk.qcow2

vhost:~# cat /proc/cpuinfo
.......
processor : 15
vendor_id : GenuineIntel
cpu family : 6
model : 26
model name : Intel(R) Xeon(R) CPU E5540 @ 2.53GHz
stepping : 5
cpu MHz : 2533.422
cache size : 8192 KB
physical id : 1
siblings : 8
core id : 3
cpu cores : 4
fpu : yes
fpu_exception : yes
cpuid level : 11
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp lm constant_tsc arch_perfmon pebs bts rep_good pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr dca sse4_1 sse4_2 popcnt lahf_lm
bogomips : 5066.70
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management:

>> it is 2x processor quadcore with 8 GB. <<

vhost:~# dmesg |grep Broad
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.6.9 (December 8, 2007)
eth0: Broadcom NetXtreme II BCM5709 1000Base-SX (C0) PCI Express found at mem 92000000, IRQ 30, node addr 00:21:5e:97:d5:e4
eth1: Broadcom NetXtreme II BCM5709 1000Base-SX (C0) PCI Express found at mem 94000000, IRQ 37, node addr 00:21:5e:97:d5:e6



situation:
i install fully virtuallization several times.
i read a lot of trouble windows 2003 server + KVM, so i try best my suitable here.
the configurtaion is almost same, with standart video graphic (in windows is detected as cirrus logic).

#1 install
a. network card : e1000
b. hdd type : SCSI
result : windows is unstable, slow response, BSOD after success installation, most of all: networrking is not working

#2 install - 2x
a. network card : rtl8139
b. hdd type : SCSI
result : windows is unstable, slow response, BSOD after success installation

#3 install - 2x
a. network card : rtl8139
b. hdd type : IDE
result : windows is unstable, slow response, BSOD after rebooted

is there any default configuration that works??
Click to expand...

i also use IDE, but with no luck. just for sure, i install wtih IDE HDD, 2x.

any help to guide me with "windows 2003 + KVM" ??
 
sub3xt1 said:
i also use IDE, but with no luck. just for sure, i install wtih IDE HDD, 2x.

any help to guide me with "windows 2003 + KVM" ??
Click to expand...

use IDE and for network e1000 - this combination is widely used. we have not yet experience from the new KVM (from 1.4beta2 and the latest virtio block and net drivers).
 
vhost:~# cat /etc/qemu-server/101.conf
name: server.mydomain.com
ide2: win_2003_EE_SP1.iso,media=cdrom
smp: 1
vlan0: e1000=62:41:37:19:7B:D9
bootdisk: ide0
ide0: vm-101-disk.qcow2
ostype: w2k3
memory: 1024
onboot: 1
description: server.mydomain.com

this combination makes networking IS NOT WORKING.
i cannot ping anywhere. but it seems responsive system.
it just cannot ping anywehre.

any help?
 
sub3xt1 said:
vhost:~# cat /etc/qemu-server/101.conf
name: server.mydomain.com
ide2: win_2003_EE_SP1.iso,media=cdrom
smp: 1
vlan0: e1000=62:41:37:19:7B:D9
bootdisk: ide0
ide0: vm-101-disk.qcow2
ostype: w2k3
memory: 1024
onboot: 1
description: server.mydomain.com

this combination makes networking IS NOT WORKING.
i cannot ping anywhere. but it seems responsive system.
it just cannot ping anywehre.

any help?
Click to expand...

I don't know why SCSI and rtl8139 doesn't work with you!
To me, it works perfectly.
I saw that the difference here is the ISO file.
We're using SP2 instead of SP1.
 
sub3xt1 said:
vhost:~# cat /etc/qemu-server/101.conf
name: server.mydomain.com
ide2: win_2003_EE_SP1.iso,media=cdrom
smp: 1
vlan0: e1000=62:41:37:19:7B:D9
bootdisk: ide0
ide0: vm-101-disk.qcow2
ostype: w2k3
memory: 1024
onboot: 1
description: server.mydomain.com

this combination makes networking IS NOT WORKING.
i cannot ping anywhere. but it seems responsive system.
it just cannot ping anywehre.

any help?
Click to expand...

did you use the very latest intel drivers (downloaded from intel web site)? the integrated drivers in win2003 looks good in device manager but they do not work.
 
tom said:
did you use the very latest intel drivers (downloaded from intel web site)? the integrated drivers in win2003 looks good in device manager but they do not work.
Click to expand...

wich NIC is better in stability e1000, virtio (in PVE1.3) or virtio(in PVE1.4b2) ?

is there a way to use virtio block inteasted of IDE in windows 2003?
 
mandrake said:
wich NIC is better in stability e1000, virtio (in PVE1.3) or virtio(in PVE1.4b2) ?

is there a way to use virtio block inteasted of IDE in windows 2003?
Click to expand...

for win2003, run with e1000 and ide, best tested and reliable.

change IDE to virtio: search the forum, I posted a howto.
 
Last edited:
You must log in or register to reply here.
Top Bottom