usb adapter

Hi everyone, I’m experiencing an issue with my Proxmox host where my second disk (used for data, not OS) isn’t detected immediately after boot. The disk is a 2.5" Crucial MX500 1TB SSD connected via a SATA-to-USB adapter, and its partition is formatted with XFS. What’s Happening: After...

Hello, I am trying to set up monitoring with Wireshark in a Proxmox LXC container running Rocky Linux 9. Some notes on my config are below: 1) I am using a Ubiquiti USW-Lite-16-PoE switch. 2) Physical port mapping on switch: My PC is plugged into port 1, Proxmox's onboard NIC is plugged into...

內容： 你好社區， 使用IC程式設計/刻錄工具時，我在 Proxmox VE （PVE） 中遇到USB設備識別問題。以下是詳細資訊： 問題描述： IC 程式設計工具在其重啟序列期間觸發完整的 USB 電源重置 （完整的電源迴圈）。 物理 USB 設備在主機級別正確斷開連接/重新連接（通過 dmesg 驗證）。 PVE 的虛擬 xHCI 控制器無法及時同步狀態更改，從而導致 USB 裝置在客戶機虛擬機中保持「斷開連接」。 技術背景： 主機： Proxmox VE 8.X 來賓：[您的作系統 - 例如，Windows 10/Ubuntu 22.04] USB...

So my built in eth adapter is no longer working. I cannot connect to the proxmox with gui I have connected a new usb ethernet adapter but not sure what to do next to make it works... I have connected desktop to that terminal and I have an access via command line I've tried to do following...

Hello all, I recently deployed a Debian VM to install the Ubiquiti UniFi Controller Software as I switched out my RAX2000 router for a UniFi U6 Mesh AP. I was able to get the UniFi software and the AP installed successfully, however, there seems to be an issue with the speeds. I installed...

I found my setup with a UGREEN USB Ethernet Adopter with the AX88179 chipset fail to bring up the USB interface. Debug logs shows `ifupdown2` failed to find the interface corressponding interface: Apr 11 22:32:28 xxxx networking[1297]: error: ifname enx000ec67988f0 not present in cache Apr 11...

I've got the need to add one more ethernet interface to the mini-pc type machines (i.e. plugging in PCIe cards is not an option) in my home lab. If I plug in a USB adapter it works fine, but gets a name that contains the hardware address (MAC) of the device: 14: enx7cc2c64a44f5...

Does anyone happen to know whether or not Proxmox VE 8.1 will automatically detect a display connected via a USB 3.0 to HDMI adapter to allow the installation to be completed on a QNAP NAS that has no video output built-in?

Hi, I'm trying to pass: baseus BA04 usb 2.0 Bluetooth 5.1 adapter root@pve1:~# lsusb | grep -i bluetooth Bus 002 Device 003: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) root@pve1:~# ls -l /dev/bus/usb/002/003 crw-rw-r-- 1 root root 189, 130 Sep 30 14:43...

I attached a Plugable 2.5Gbe USB adapter to my Proxmox install, my goal is to assign it to VMs and get the higher throughput and also to use it for backups/restores to my NAS. They are attached to a 2.5Gbe switch. I can't seem to get the drivers working on Ubuntu, I installed the Realtek 2.5Gbe...