Search results

Since this post is a lot shorter than the other one and a lot quicker to get to thee solution. Just do what LeeSteken says. NOTE: you have to change it in 3 places to the new network interface. :)

It might be a simple fix but if you have been messing with your network i.e. adding a bond etc. make sure on the linux bridge , normally, vmbr0 - you have set the gateway to the IP address of your router i.e. 192.168.0.1 if it is blank then nothing will update thanks

100% agree. The Intel Enterprise SSD wipe the floor with them. Thanks

With ceph - if you have a 5 node system. With some nodes having dual NVME for CEPH, Samsung PRO Why do they preform so badly compared to Intel Enterprise SSD or any other SSD? The NVME drives show a latency of 1000+ compared to the SSD with a latency of 2+ Even on the same node. On the other...

With ceph - if you have a 5 node system. Each node has a 2x 1 GB and 2 x 10gB on a single card 2x 1GB are motherboard 2x 10GB are single PCIe card NIC is it better to use the 2 x 1GB Bonded for proxmox and 2x 10GB for Ceph please assume all Nodes are i9 CPU/motherboards / DDR5 Ram etc...

Hi Guys My Draytek router just died, YES NOT A GOOD DAY at the office!!!!! Got it all back and running after 4 hours of %^$%IN S(&T. Looking for a new router (non Draytek) I went to the local computer shop and got a TP-Link (don't flame me) and it worked well. Problem is it isn't Multi WAN. So...

/nodes/DC4/qemu gives me the name of the VM and the VM number

Hi Guys, I am after a command or group of commands to get this details of the Virtual machines on all nodes node name , node IP , VM name , VM IP address , VM number I have used "pvesh get /cluster/resources" "pvesh get /cluster/status" which gets me node name , node IP , VM number but I...

Hi Guys (and Gals) I have a 4 node cluster and am going to install CEPH again from scratch. each node has 1 x 10GB NIC and either 1 or 2 x 1GB NIC I have (seperate) both 10GB Switch and a 1GB switch. less than 20 VM's (all VM's are windows 48GB C: drives) Lots of Ram will set up the CEPH...

HI Wolfgang, thanks for the links and I will give it a go tonight. corosync looks to be running now but since all the nodes have dual NIC's I will set up a separate network. systemctl status corosync ● corosync.service - Corosync Cluster Engine Loaded: loaded...

my 2cents if it is a single node (server / PC) then put it all on a SSD don't worry about ZFS (don't flame me) as it really wont help you. If you have multiple SSD or HDD or a combination on a single node then dont bother about it. If you have the option buy a cheap QNAP or similar box which...

My PROX 4 goes from a green tick to a red X in the GUI the CEPH has a drive on PROX 4. CEPH always stays all green. If i turn of the node PROX4 and leave it off for 30 minutes then turn it on then CEPH goes all red but after about 10 minutes it goes all green EVEN THOUGH PROX4 MIGHT HAVE A...

if anyone this error here is the solution. migrate the VM's to another node shutdown the node start the node problem gone. :)

Hi All, I have 4 nodes in a cluster Node 2 is the primary node and I can add disks (create OSD) connected to this node with no problems. The other 3 nodes all have spare SSD drives but none of them will appear when I try to add an OSD when I try to destroy the contents I get this...

Hi Guys, thanks for the recommendations. In the end I copied all the VM's over and started again. All working now PS - I had tried pvecm updatecerts

using the shell and logged directly into prox1 ssh: connect to host prox4 port 22: Connection refused ssh: connect to host prox3 port 22: Connection refused :(

sorry - most recent version of Proxmox 6.0-4 4 nodes in a cluster

Hi All, had it working wonderfully and then I had to go and reck it all. when I try to migrate a VM from one host to another I get this message 2019-09-27 19:07:52 # /usr/bin/ssh -e none -o 'BatchMode=yes' -o 'HostKeyAlias=prox3' root@192.168.0.112 /bin/true 2019-09-27 19:07:52 Host key...