Search results

I finally figured it out. It turned out to be a bad SATA cable. It was just random that it worked when I tested on the other volume. It was very intermitted, probably changes in the cable due to vibration or something like that. That was quiet the trouble shooting.

I just had another idea and tried to mount the ntfs partition in linux and copy it that way. Doesn't change anything. It copied like 12MB in ten minutes. I also ran ntfsfix without any success.

Ich habe bewusst Datacenter SSDs gewählt, weil ich bei meinem alten home server mit consumer SSDs das problem hatte, dass die nach ein paar Jahren schon Probleme machten. Die Performance ist mehr als ausreichend für meine Anwendung.

Es sind Samsung PM9A3 SSDs. Aber das Problem habe ich mit dem HDD pool aus drei Western Digital Red Pro HDDs. Wobei ich nicht glaube, dass es an den HDDs liegt, weil ich mit einem anderen volume im gleichen pool gar kein Problem habe. Da habe ich über SMB mit 10Gbps Ethernet transfer speeds von...

Little update. The scrub is still running but the remaining time is now way shorter. But still no errors found. scrub in progress since Sat Jul 27 12:46:30 2024 2.60T / 7.02T scanned at 34.3M/s, 1.69T / 7.01T issued at 22.3M/s 0B repaired, 24.07% done, 2 days 21:36:27 to go Any...

Here you can see the active time. It is copying the entire time. Most of the time not doing anything and sometimes there are bursts where it does copy and then the active time goes down when it does work.

Hi, I have a pretty weird problem and I am out of ideas and can't find anyone that has the same problem. I would be really grateful for some ideas. Background info: I have one Proxmox host with an AMD EPYC 7443P, 128 GB RAM and three ZFS pools. One is mirrored with two 1TB NVME SSDs One is...

I just noticed another problem with that solution. I added a new VNet through the GUI and that removed the IP address and gateway from the config file. If I know it it's not a big deal, but it's something to watch out for.

Thank you! That works, why didn't I think of this, it's so simple.

I tried it with the vmbr0.101 configuration now. That itself does work the same as with vlan101. I don't remember the reason I switched over to the vlan101 config, I thought the old way stopped working, but maybe there was another reason. I can also apply the SDN config now, but apparently that...

Hi everyone, I just updated to from 7.4 to 8.2 and wanted to look into the new SDN features. I have one vlan aware vmbr with one vlan interface on it that I am using for the management IP of the PVE host. It this vlan (101) are also other servers. My problem is, that SDN apparently doesn't like...

Thank you, I added it on the Bugzilla.

Hi, I am trying to configure DKIM signing for all domains on the gateway but with the same d= tag in the signature. So there is one DKIM Key and DNS record, say on domain-x.com. The gateways are also called mail01.domain-x.com and mail02.domain-x.com. Now I want PMG to DKIM sign all outbound...

Does anyone have an idea what I could try?

Hi, I am running OPNsense in Proxmox and I would like to get the balloon driver working properly so I can get correct memory readings in Proxmox. Right now for example Proxmox reports 3.35GB/4GB while OPNsense itself reports only 740MB is used. I have searched a lot online and found some...

Yup, that's the problem. Thank you very much! I didn't update the iqn after I reistalled the NexentaStor VM because it had a problem. Works perfectly fine now, thanks again :)

From both nodes: 192.168.2.20:3260,2 iqn.2010-08.org.illumos:02:eeb20392-e098-cdb7-94e3-c884f5156d16

Hi, I have the following setup: 2 pve nodes in a cluster, the first node has a VM with NexentaStor running on local storage. The Nexenta VM has some disks passed trough and configured in RAIDz1 and is configured as an iSCSI target and there is also a NFS share for ISOs. I want to use the zfs...

Thank's for the quick answer but I think that's not the problem, if I disconnect the UPS, my script shuts down the filserver via ssh and should do "shutdown -h now" on the local system. And that doesn't works. If i type "shutdown -h now" manualy after the script sent the schutdown cmd to the...

Hi, I've got a APC SmartUPS-1000 a few days ago to protect my Serverrack with 1 Fileserver and 1 Proxmox Host (2 in the furure). At the first i tried to use nut, because its included in Openfiler which is my Filserver Distribution, but I didn't get it working. I'm useing apcupsd on the Proxmox...