Did you block the nvidia driver as I indicated in my post? It's necessary.
The other way is to ignore the Proxmox Kernel and go with Debian Kernel.
My config as documented in my own wiki:
echo blacklist nouveau > /etc/modprobe.d/blacklist-nvidia-nouveau.conf
echo options nouveau modeset=0 >>...
On my email system we support aliases. Users get quarantine notifications for the 'sent to' email address and for their base address. When accessing the quarantine, they see all spam regardless which login link they use.
When using the base address link, they get error message "Error 403...
The kernel includes a buggy kernel module nvidiafb.
You may remove it using a blocklist and regenerating initramfs yourself.
Or - Proxmox Team removes it in the official kernel.
I did it, my Hetzner server boots flawlessly.
Question to kernel gurus
Is it safe to disable the driver following this post?
https://linuxconfig.org/how-to-disable-blacklist-nouveau-nvidia-driver-on-ubuntu-20-04-focal-fossa-linux
Any help will be appreciated.
Thanks, Birger
Hi everyone,
I just ordered a new AX41 server at Hetzner and tried to install PVE 8.0.
Base is Debian 12 Bookworm, I use the installation from https://pve.proxmox.com/wiki/Install_Proxmox_VE_on_Debian_12_Bookworm. At least I try to...
pve-kernel-6.2 hangs on boot. I gave pve-kernel-6.1 a try...
I did successfully debug /usr/bin/pmgqm and found line 298 in /usr/share/perl5/PMG/CLI/pmgqm.pm, which suppresses the spam report. After modifying this line to TRUE, the spam reports get sent.
A little bit of reading through the code showed, it depends on a list of domains considered intern...
Still no solution...
I just checked again, there is still no PMG LXC template version 7. So my way, installing 6.4 and upgrading is the only solution.
How can I check, what went wrong on upgrade?
Is there any hash-checker for /usr/share/perl5/PMG?
Is there any configuration checker?
Thanks, but I did all the checks. By now I see 26 entries with pmgqm status, I also see 26 entries for today in the GUI. Output of pmgqm send -debug 1 -timespan today outputs nothing...
I did a quick perl -d -T /usr/bin/pmgqm send -debug 1 -timespan today. I stepped into some subroutines but...
I have to add, I did install LXC version 6.4-1 and upgraded in-place to 7.0-7 according to https://pmg.proxmox.com/wiki/index.php/Upgrade_from_6.x_to_7.0.
With a lot of reboots after that, because I edited my postfix templates.
Rebooting to be sure, that the configuration always works after...
I do not get any spam reports.
Using the commandline
pmgreport -debug 1
works, I also get daily usage reports
pmgqm status
lists all users and # of spam in quarantine
pmgqm send -debug 1
empty output
Do you have any hints, where to look for?
Version Mail Gateway 7.0-7
LXC installation on...
Remember the time when you implemented Apache HTTPD - IP based virtual hosts. ;)
You did this using multiple IP addresses on your physical interface (IP address aliases).
It was Pre-SNI technology (see RFC 6066).
This traditional setup might not work with a server at Hetzner.
They have set up a lot of security mechanisms. If I remeber correctly, they accept only your physical MAC-address at your outside interface, that's why they describe a routing setup for the secondary address.
If you give your...
You may read Hetzner DokuWiki about additional IPs at https://wiki.hetzner.de/index.php/Zusaetzliche_IP-Adressen/en.
While there are different setups, personally I like the following:
add secondary IP address as alias to Proxmox physical interface (vmbr0 or eth0, as you like)
create a bridge...
ok, just a small environment.
I'm used to have larger environments, dozens of networks and several
handful of distributed pfsense firewalls in a cluster.
But these do not have any in common with your setup. So I told about the server above.
But I do have more than one pfsense firewall even in...
My eth0 is just an ancient relict, it works the same with vmbr0.
Host isn't open, it is controlled by iptables. As I use iptables to DNAT to the pfsense firewall, I do control, which ports are accessible. Host has no additional ports open. Even ssh gets redirected to pfsense firewall.
My...
I have a similar setup on a hosted Root-Server (Hetzner).
I have only one IP, assigned to eth0 not vmbr0. On eth0 I have some iptables-rules for NAT.
I do NAT on proxmox host level (configured via /etc/network/interfaces).
I have vmbr1 as internal bridge. It only works as WAN interface for my...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.