Search results

Hi there, have updated node from 7 to 8.3.2 On one node with one CT, there is snapshot not possible. Initial, the cube followed by NOW is missing too: When doing a snapshot, the task is done but not displayed in list. Doing the snapshot again "TASK ERROR: snapshot name 'test' already used"...

Everything is working well. Installing 7.2 from ISO instead of upgrade from 6.4 to 7.2 solves the problem with accessing the tape drive.

Have make a clean install of 7.2 from ISO, now I can handle the tape drive from the node: root@pve4:~# mt -f /dev/st0 status drive type = 114 drive status = 1543503872 sense key error = 0 residue count = 0 file number = 0 block number = 0 At the moment I add the node back to the cluster and...

I will do now a clean install of 7.2 on this node and if the tape can not be used from the node, I will reinstall 6.4 to get working my Bareos Backup System inside the CT.

Hi there, I have done the upgrade from 6.4 to 7.2 with a node, where a tape drive was used. After upgrade, I can't access it (QUANTUM ULTRIUM-HH7) from the node (LXC CT not tested because node must working first): root@pve4:~# lsscsi -g [1:2:0:0] disk LSI RAID 5/6 SAS 6G 2.13...

Hi there, I'm using a NFS export as storage for VM/CT backups. Working well. Now, for maintenance, the server which provides the NFS export hast to be reboot. What would be the best way, to tell the nodes, that this export is temporary not available? A backup is not planned during this time...

Will this procedure make it possible to run Centos 7 in LXC containter under Proxmox 7?

Brining this question up again, I'm planning to upgrate to 7.0 but want to have clearness, that this problem will not destroy anything. Are additional information needed? Thanks.

Hello, I have add a mount point, based on a hardware RAID-0 (Stripe) to a CT: Inside of the LXC container, I get: # df -h Dateisystem Größe Benutzt Verf. Verw% Eingehängt auf rpool/data/subvol-211-disk-0 200G 133G 68G 67% / /dev/loop0 6,8T 1,3T...

Ok, done. Test after update-grub # cat /boot/grub/grub.cfg | grep "lax" linux /ROOT/pve-1@/boot/vmlinuz-5.4.106-1-pve root=ZFS=rpool/ROOT/pve-1 ro root=ZFS=rpool/ROOT/pve-1 boot=zfs quiet acpi_enforce_resources=lax linux /ROOT/pve-1@/boot/vmlinuz-5.4.106-1-pve...

Thanks Dominik, The git of a1wong doesn't support the IT8665E. But this https://github.com/frankcrawford/it87 has it included. Cloning the git and making install was done successful, but can't load the module: The new module is available: # ls -l...

Hi there, I want to monitor the temperature and voltage of the mainboard. sensors-detect says: Driver `to-be-written': * ISA bus, address 0x290 Chip `ITE IT8665E Super IO Sensors' (confidence: 9) Note: there is no driver for ITE IT8665E Super IO Sensors yet. Check...

Thanks, you're right (last line): zfs list NAME USED AVAIL REFER MOUNTPOINT rpool 39.3G 410G 104K /rpool rpool/ROOT 11.6G 410G 96K /rpool/ROOT rpool/ROOT/pve-1 11.6G 410G 11.6G /...

Thanks fabian, but here is on the target node (pve3) not such volume: root@pve3:~# ls -l /rpool/data/ total 59 drwxr-xr-x 18 root root 23 Dec 22 07:54 subvol-172-disk-1 drwxr-xr-x 18 root root 23 Feb 1 17:47 subvol-183-disk-0 drwxr-xr-x 18 root root 23 Feb 1 17:47 subvol-184-disk-1...

Replication of container works: from pve4 to pve1 and pve2 to pve3 not. The log: 2021-04-15 09:50:00 211-2: start replication job 2021-04-15 09:50:00 211-2: guest => CT 211, running => 0 2021-04-15 09:50:00 211-2: volumes => pve_zfs:subvol-211-disk-0,pve_zfs:subvol-211-disk-1 2021-04-15...

pve-manager/6.3-2/22f57405 5.4.73-1-pve #1 SMP PVE 5.4.73-1 There is no HA membership, the node is only part of a cluster with one CT (211) on it. Inside the LXC container, Bareos (bakula fork) is running with a Postgresql DB. Command: command 'lxc-stop -n 211 --nokill --timeout 60' failed...

After reading our task logs we've done on the machine, we found this: The node has a built in LTO streamer, in a LXC container Bareos (Bacula fork) makes the job for the backup. There is used "backup to disk" before "disk to tape" to avoid start-stop issues with the tape. The tape works with...

Yes, with other Linux distros I work, I have this possibility to select a kernel or have line for manually adding parameter for the kernel I want to boot. But not here. Have tried it 3 times, hitting the down or up arrow key, only this menue comes up: Where is coming from the "macOS" tab? This...

Its a ASUS Prime A320M-A Board with CPU socket 1331 CPU: AMD A8-9600 Radeon Sorry for asking, how can I select the kernel I want to boot? After starting up, I can only select "Start Proxmox PVE" or reboot to Firmware setting (BIOS). Have booted from an USB drive with the Proxmox Iso installer...

Hi there, I did update a node to the latest available version of PVE today. After rebooting, I can ping the node but get no access via SSH or GUI, also not from an other node of the cluster. When I plug on a video monitor, the displaying of the boot up sequenze will end with a blank screen and...