Search results

Well, it depends on your configuration. If your PBS datastore is in a ZFS dataset then you need only to turn ATIME on on the dataset zfs set atime=on POOLNAME/BACKUPDATASET If you use the entire pool as PBS datastore, then you need to enable it on the pool. zfs set atime=on POOLNAME

Real world date, not benchmarking RAM. It is terribly slow. INFO: 0% (208.1 MiB of 1000.0 GiB) in 3s, read: 69.4 MiB/s, write: 33.4 MiB/s INFO: 1% (10.0 GiB of 1000.0 GiB) in 5m 18s, read: 31.9 MiB/s, write: 31.3 MiB/s

You are benchmarking your RAM. Think about it, which HDD do you know that can write more than (average) 120Mb/second? Mirroring does not make that twice as fast..

I stopped the creation of disk "2". Created a new vm on the target vm and mounted the disks it already had copied. Mission complete. No reason to wait for another 6 hours while it does illogical stuff..

PS: One of the best solutions for ZIL is one of these, or two: https://www.radianmemory.com/edge-card-rms-300/

A slog device usually does not need to be much bigger than 10-20GB as they only need to hold few seconds of data before they are written to the underlying storage devices disks or ssd. The problem is that the ZIL afaik does not support TRIM apt-get install nvme-cli nvme<TAB> You will find a...

Are you certain your NVMe is designed to the heavy rewrites happening on the SLOG device? If you are using consumer grade hardware the lifetime of your SSD will be around 1-4 weeks depending.. You would probably also want to mirror your SLOG device. It is no fun to loose the pool due to a...

Yes, it worked with dist-upgrade

It takes half a day to copy Disk0. Then it copies the EFI disk which is fine. Then it realizes it has already create Disk0 and decides to create disk2 and format it again.... Why? There is no disk2on the host... There was Disk0 1TB and Disk1 an EFI disk... Task viewer: VM 110 - Migrate...

They are all default options indeed apart from hostname, email etc. 127.0.0.1 localhost.localdomain localhost 10.0.0.223 pvetest.winwinsol.local pvetest # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix...

In Denmark 30 minuttes are fast :) reproduction steps: Download ISO Install Proxmox 6.2-1 Add proxmox non-sub apt source apt-get update apt-get upgrade

I will create a virtual server and install proxmox from iso again. It will cause the same error message. It has done so on every host I have installed so far. I suspect it is because I have joined the server to a cluster prior to the update. I will try not to join the server to a cluster and...

I rebooted the system already, I am not sure it is still in the output :/ However, I attached what is presently output by journalctl -xe

I forgot to note that I had joined the node to a cluster immediately after installation and before the update/upgrade command was issued

.... Setting up pve-ha-manager (3.1-1) ... Job for pve-ha-lrm.service failed because the control process exited with error code. See "systemctl status pve-ha-lrm.service" and "journalctl -xe" for details. Job for pve-ha-crm.service failed because the control process exited with error code. See...

Hi there, Whenever I do a clean install of proxmox 6.2-1 from the downloadable ISO and subsequently run apt-get update/apt-get upgrade I get the following error and was wondering if that is a problem or not. I usually run apt-get dist-upgrade to get to 6.2-11 afterwards Setting up pve-manager...

I installed samba and upload it that way :)

Odd. Its kinda like coming home from shopping and put the groceries in the toilet and then go to the kitchen, go back to the toilet, pick up the groceries, go back to the kitchen and store the groceries in the fridge ...

I created it in CLI indeed. Its a very old pool that I imported :) It automounts on boot. I have vm's starting on boot from the pool. If it doesnt automount ZFS cant mount at all because proxmox creates new fólders inside the /storage/vm folders. I have to remove the storage in proxmox so that...

My ISO directory is located in a ZFS folder /storage/iso/template/iso If I attempt to upload images with the GUI, it seems that proxmox wants the iso file to be stored on the root drive which is inconvenient as it is a USB drive. It is also not what I am asking proxmox to do. I am asking it to...