Search results

Hi - I hope it is not an error but it's always good to check just to make sure.

Hello Moayad - here is the output of journalctl -b. Thanks very much.

Apologies for replying until now but with the year end holidays it was busy. I entered the pvecm updatecerts -f command and it updated them. Rebooted and the low memory entry is still showing in the syslog. So I ran the journalctl -u pveproxy and this is what I got: -- Logs begin at Sun...

Thanks very much for you reply Moayad, below is the full output of pveversion -v: proxmox-ve: 6.3-1 (running kernel: 5.4.78-2-pve) pve-manager: 6.3-3 (running version: 6.3-3/eee5f901) pve-kernel-5.4: 6.3-3 pve-kernel-helper: 6.3-3 pve-kernel-5.3: 6.1-6 pve-kernel-5.4.78-2-pve: 5.4.78-2...

Hello, Running Proxmox on this box with 32Gigs of RAM and ZFS. Today I logged in and all the VMs and the server had a question mark on it. I rebooted the server and it took a while to restart. I looked at the syslog and found the low memory corruption entry. Can anyone please take a look at...

Ok thanks very much for you help.

I downloaded and ran the intel microcode, rebooted but when I run = dmesg | grep 'microcode' I still get this: that's what I got before I installed the intel microcode. is there a way to check if somehow the installed failed or something happened?

Thanks very much for the reply Wolfgang. I have not installed that yet. Just a question - do I just need to add to the package repository /etc/apt/sources.list the line deb http://ftp.us.debian.org/debian sid main non-free and then run sudo apt install intel-microcode? then reboot and that...

Hello everyone, I have a DELL Poweredge T610 running PROXMOX. I have three VMs on it. For the last month, it just freezes and does not respond to any commands. The VMs show up as having a high RAM usage and the only way to get it back up and running is to do a hard reset, pushing the power...

Hi SB-JW, I have uploaded the pics of the server when it boots and the output of the sas2flsh. Why is there two ?? besides SAS2008? The next pic besides Firmware product ID shouldn't it say IT besides the 0x2213? If I want to boot from the Hard drives attached to the card I...

I was just quoting your answer but I did a terrible job at that, lol... This is what I wrote not in italics: I will take a picture(s) when I get home and upload them. I am not at home right now. To confirm - you are advising NOT to re-flash the IT mode BIOS to the card again? If I get a linux...

Oh - I flashed the BIOS on the card as per the guide that I followed on the link I posted in my original post. How can I check if the BIOS on the card sees the drives? The thing is when I boot the server, I used to get a message that the configuration for the controller/drives was missing and it...

Not sure how to see the BIOS of the H310, is this the same as the BIOS for the server? If yes, then no, I am not able to see the drives there. When the controller is enabled, in the BIOS and the USC on the server, the RAID controller can be enabled and disabled but there is no option to change...

Hi sb-jw, thanks for the reply. Yes I did, before I disabled the perc 6/i controller I was able to see the four drives no problem.

Hi everyone, I have a Dell Power Edge T610 server that I want to install PROXMOX using ZFS. I have four 1TB hard drives that I want to use, I flashed an H310 card I found to IT mode LSI using this guide Everything went well, no errors, no issues. I used this guide as the H310 card came from...

Hi, I have a Dell T610 power edge and a H310 card. I have 4 one TB HDs that I would like to install proxmox with zfs. Do I need to flash the firmware on the card or should it work out of the box with the info above? Or can I just attach the 4 hard drives to the onboard sata slots and go...

Hi caslicomputers, Were you able to resolve this issue with your Windows Server 2016 vm? I found this post as I am having the same issue like you do with a Windows Server 2016 Domain Controller. I just started 5 days ago and there seems to be two blue screens. Funny thing with me, I have...

Thanks very much for your help. The restored worked!

Thanks to both for the information. I backed up the VM that is located on that HDD but after I restored it to ZFS, I started it and it boots but it does not get past the Windows logo. The backup mode I did was a snapshot. If I do a stop mode backup, does it make a difference? Will it...