Hallo, ich habe auf zwei Nodes (Community Edition) das Update auf pve-manager/6.2-6/ee1d7754 eingespielt. Danach starten die VMs nicht mehr. Weder automatisch noch manuell.
Im Task Manager steht jedoch der Status "ok"
Node 1 mit Subscription blieb unangetastet auf pve-manager/6.2-4/9824574a...
Also.. ich habe jetzt corosync-qnetd deinstalliert, da der auf dem Node nichts zu suchen hat.
Jetzt funktioniert alles.
Danke für die geschätzte Aufmerksamkeit
Ich bin immer noch auf der Suche nach einer Lösung, warum ich den Service auf Node 2 nicht enabeln kann.
Lässt sich daraus was entnehmen?:
root@proxmox2:~# ls -l /lib/systemd/system/*coro*
-rw-r--r-- 1 root root 453 Feb 4 2019 /lib/systemd/system/corosync-qdevice.service
-rw-r--r-- 1 root...
Neu Installation hat funktioniert:
Generating key. This may take a few moments...
Notice: Trust flag u is set automatically if the private key is present.
QNetd CA certificate is exported as /etc/corosync/qnetd/nssdb/qnetd-cacert.crt
Created symlink...
also auf 192.168.3.1 (Centos 7/Nethserver) läuft definitiv kein corosync
[root@v-nethserver etc]# ls /etc/
<...>
clamd.d
cockpit
collectd.conf
collectd.d
conntrackd
cron.d
<...>
Ich werden Raspi wohl noch...
aber auf dem Raspi sieht es nun defekt aus, owohl nach der Installation der Status o.k. war:
root@proxmox3:~# systemctl status corosync-qdevice.service
● corosync-qdevice.service - Corosync Qdevice daemon
Loaded: loaded (/lib/systemd/system/corosync-qdevice.service; disabled; vendor preset: e...
Ha, den Tipp hatte ich glatt überlesen ...
DAs wars
root@proxmox2:~# systemctl status corosync-qdevice.service
● corosync-qdevice.service - Corosync Qdevice daemon
Loaded: loaded (/lib/systemd/system/corosync-qdevice.service; disabled; vendor preset: e
Active: inactive (dead)
Docs...
ich habe mal jeweils die corosync.conf verglichen:
Auf Node 1 und 2 sind sie identisch und weisen den Raspi (192.168.3.203) als QDevice aus
quorum {
device {
model: net
net {
algorithm: ffsplit
host: 192.168.3.203
tls: on
}
votes: 1
}
provider...
Was müsste ich hier machen?
Ich habe nochmals das Setup von Node2 aus durchgeführt und den Raspi auf 192.168.3.203 von dort aus adressiert. Was anderes fällt mir nicht ein...
root@proxmox2:~# pvecm qdevice setup 192.168.3.203
QDevice already configured!
root@proxmox2:~#
Ich habe dort aber...
Danke für den Tipp, mal sehen, ob ich das Manual umgesetzt bekomme. Bis jetzt ist mir der Unterschied noch nicht klar, da ja auf dem Raspberry ohnehin keine volle Proxmox-Installation möglich ist und ich den Raspi nur als Qurum-Node nutzen will; er liegt halt hier so in er Ecke rum.... QDevice...
Hallo zusammen,
ich betreibe seit einer Woche erstmals 2 Proxmox-Nodes im einem Cluster und würde gern einen weiteren Node als Quorum (Raspberry Pi 3 Model B Rev 1.2) in den Verbund aufnehmen.
Dazu habe ich folgende Anleitung (auf Basis Debian Buster) umgesetzt (falls ich das richtig...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.