Recent content by Lokytech

I'm speaking after finishing my first migration of 24 servers. What i can say is : BEFORE The risk is a full shutdown. You should not run with fragmented versions for a long period of time. You can migrate VM from 8 to 9 but not from 9 to 8. There is always a risk. But i did it with to iSCSI...

Thank you for sharing. Here is my config for HAProxy and it works with noVNC : frontend SSL_PROXMOX bind 11.11.11.11:8006 name 11.11.11.11:8006 no-sslv3 no-tlsv10 no-tlsv11 no-tls-tickets ciphers...

For the last generation server, you should 100% go to iDRAC monitoring instead of OMSA. I still keep OMSA for PE2950, NF500, R610. For newer generation server, i did try iDRAC and and i can get the same level of information in my Centreon as well as managing the storage controller avec virtual...

I cannot edit anymore the first post. Here are my findings with Debian 13, Proxmox 9 and Dell OMSA 9.3. Everything works except the key importation as apt-key is removed from Debian 13. echo "deb http://linux.dell.com/repo/community/openmanage/930/bionic bionic main" >...

Successful install of 9.30 bionic onto the latest Proxmox-ve 9.0.10. Target machine : PE2950, NF500, R610, R430, R730 and R740 @neocharles: I also have those message. Some research told me it's just some warning/informational message.

@sb-jw Thank you for your feedback. I'm gonna check checkmk, did not know it existed. Can you also check for bad memory stick (ECC errors) and Predictive disk failure through it ?

Thanks guys for keeping this thread alive. @sb-jw : Why do i use OMSA ? OMSA use smuxpeer to fill SNMP. Then i use https://github.com/trondham/check_openmanage with Centreon monitoring. I'm like @CTCcloud. Long time using those system and no need to teach the new recruit. Ease of use.

Hi all, I cannot edit the 1st post to update the steps anymore. Thank you for your feedback.

Thank you. I've planned to migrate one of my cluster to 8.0 this Monday. Please, I would love your feedback on 8.0 if you succeed. Edit: I did the upgrade but was stuck at boot with Service Networking/starting (xxx minutes / nolimit). The problem was ntp that was replaced by ntpsec and block...

Never tried it. Because it's OME and not OMSA (OpenManage Server Administrator).

Same here. I've upgraded to pve-qemu-kvm_6.1.0-3 and no more IO issue on VirtIO disk.

Thank you everyone for your feedback. I've updated the main post with them.

In that case, enp129s0f1(node3), enp129s0f0(node2) should be slave of vmbr1 and the ip should be configured on the vmbr1. Right now, your bridge vmbr1 is not connected to any network interface. How could it communicate with the outside of your server ? in this situation VMa(on node2) and VMb(on...

I've got Proxmox on multiple Dell servers (from 2950 to R740) H700 will work without problem. H310 wont work. You have 2 choices : Either do not use RAID or use mdadm software raid. In my opinion, if you have a shared storage (iSCSI, NFS, Ceph) you dont need raid for the system. I've been...

I've done it differently. On the switch : - the port where the box is connected is UNTAG on VLAN 42. - the port where the proxmox is connected is switchport mode trunk allowed vlan 1,42 with vlan 1 untag. On proxmox : - vmbr0 is not vlan aware - the pfsense has 2 interface virtio : the first...