Hi everyone,
I was wondering if I could get some suggestion for setting up temporary scratch space for non-critical data.
Best balanced I/O performance (typical file size ranges 50k ~ 1MB each) is the priority.
VMs (volblocksize = 16k) are all on ZFS-mirrored enterprise U.2 SSD.
But the...
The original ideas are from:
https://forum.proxmox.com/threads/serial-port-on-host-to-proxmox-console.81045/
https://help.ubuntu.com/community/SerialConsoleHowto
https://tldp.org/HOWTO/Remote-Serial-Console-HOWTO/configure-kernel.html...
Hi Dominik. Thank you for the reply.
1. I meant the blacklist.conf and vfio.conf were copied to both kernel.
My goal is to only apply those two to one of the kernel.
In an event that I bricked the latest kernel, I can still boot to the other kernel to make changes (like ip address).
Otherwise I...
Hello,
1. Because I passthrough the only graphics card, once the PVE gets to "Reading all physical volumes...", I no longer can use the console.
If I make some change that lock myself out of web interface (for example, change network config), I guess that I have no way to get into the system...
Can I bond NIC1 and NIC2 with bond-broadcast mode and only have one bridge for NIC2 and VMs only see one network interface and being able to access the NIC1's internet?
Thanks!
Due to some restrictions, I have to use two NICs on my Proxmox node in the following way:
For example:
NIC1: 10.10.10.xxx, just one IP assigned by the facility to the Proxmox Node, able to access internet via their firewall
NIC2: 192.168.150.xxx, connected to my own router (192.168.150.1)
Can...
Like stripe Disk 1 2 3 <-mirror-> stripe Disk 4 5 6?
I probably didn't (I used all defaults), is there a way to check it now?
Yes. These I know. my total capacity utilization is 11%.
Four SSDs are in Asus Quad Card with fan, at 35C. The other two are under motherboard heatsink, which is a...
Hi all,
PVE: Latest 6.4-5 (PVE 5.4.106-1)
Total system RAM is 256GB
SSD is WD SN750 2T x 6 in RAID-Z2, compression=lz4
VM : cache=writeback discard=on, size=501G, ssd=1 (see attached code)
VM Crystal Disk's RND 4K and IOPs are much slower than individual drive in bare-metal system.
Some other...
Read a lot and final find a working solution.
Reboot.
When it gets to start menu GRUB.
1. Edit grub command line (press 'e' key )
from
initrd=\EFI\proxmox\5.X.X-X-pve\initrd.img-5.X.X-pve BOOT_IMAGE=/boot/linux26 ro ramdisk_size=16777216 rw quiet splash=silent (Or whateever is there)
to...
Hello,
Urgently need help. I have research work data on it:oops:
Story:
My GPU passthrough has been working well on both 6.2.55 and 65. Because I used update-initramfs -u -k all, both .55 and .65 has GPU frame buffer disable thus no host display out. I was trying to reverse GPU passthrough...
I have an old one-slot Quadro card that I can use.
Or I can buy a "ZOTAC GeForce GT 710 1GB DDR3 PCIE x 1" in slot 4.
(that way I can still use slot 2 for 10G NIC and slot 8 for 2nd GPU for deep learning on slot 5 with PCIE riser)
Currently, I have a 2080Ti on PCIE slot1 (x16) and ASUS Quad...
Good point.
My motherboard does not have serial COM port on the back panel, nor does serial COM header on the board.
Is that something that can be added using USB-serial COM or PCIE x 1 serial COM card.
I have other computer to use. Even a very old one that has serial COM on motherboard back...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.