bbgeek17's latest activity
-
bbgeek17 replied to the thread [TUTORIAL] What Replaces SRM and vSphere Replication on Proxmox?.Thanks, this is great detail. The command transcript especially. With krbd the snapshot mode should be fine since it doesn't need the journaling feature on the image. Journal mode is a different story though. There was a full patch series for... -
bbgeek17 reacted to christophe's post in the thread [TUTORIAL] What Replaces SRM and vSphere Replication on Proxmox? with
Like.
Hi @bbgeek17, In our context, we are preparing configurations intended to be instantiated by non-specialist departments; we are therefore prioritizing ease of implementation. 1. At the very beginning we followed multiple docs, mainly... -
bbgeek17 replied to the thread RDMA Requirements for Proxmox with ZFS and Third-Party iSCSI Storage.Hi @Rajan_Kumar.Jaiswal@sita. , welcome to the forum. Following @Francois Baillargeon suggestion, you may find some useful information here: https://kb.blockbridge.com/technote/proxmox-tuning-low-latency-storage/ Blockbridge : Ultra low...
-
bbgeek17 replied to the thread [TUTORIAL] What Replaces SRM and vSphere Replication on Proxmox?.Thanks, @christophe! That's more configuration coverage than most reports we've found. "The multi-cluster equivalent of intra-cluster pvesr" is a good way to put it. Since you've run both modes in both directions, a few things you're in a rare...
-
bbgeek17 posted the thread [TUTORIAL] What Replaces SRM and vSphere Replication on Proxmox? in Proxmox VE: Installation and configuration.Hi Everyone, Disaster recovery keeps coming up with folks moving off VMware, usually as some version of "what replaces SRM?" We've answered pieces of this in threads for years, so we finally sat down and wrote the whole thing up properly...
-
bbgeek17 replied to the thread VIRTIO SCSI vs VIRTIO SCSI single.Hi @xybo, yes that applies to ZFS as well! Cheers Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread VirtIO Block or IDE.Hi @Sisdyiyy , welcome to the forum. We have covered the performance comparison between the windows controllers in our KB here: https://kb.blockbridge.com/technote/proxmox-optimizing-windows-server/part-4.html Hope it helps in your decision...
-
bbgeek17 replied to the thread Upgrade from Proxmox VE 8.x to 9.2.1 instead of the latest 9.x.Hi @powersupport , This topic has been discussed recently over here: https://forum.proxmox.com/threads/upgrade-from-proxmox-ve-8-4-x-to-9-1-veeam-related.185270/#post-862853 The answers to your questions are: 1, No 2. Not sure if older packages...
-
bbgeek17 replied to the thread [TUTORIAL] Proxmox VE vs VMware ESXi performance comparison.Hi @grass127, We do have a lot of this data internally, but it isn't organized as methodically as the original tech note was, so it's hard to publish anything rigorous. What I can tell you is that the relative changes in performance are not...
-
bbgeek17 replied to the thread Upgrade from Proxmox VE 8.4.x to 9.1. Veeam Related.Hi @hishamrixs, welcome to the forum. While I understand, and often share, the sentiment expressed by other posters that different backup products might be better suited to your particular use case, we also have to recognize the business and...
-
bbgeek17 replied to the thread NVMe Over TCP - Proxmox VE.A few notes based on our experience with NVMe/TCP and PVE: Your performance expectation should come from your storage stack, not your choice of protocol. The transport is usually not the bottleneck in setups like this. If you're seeing latencies...
-
bbgeek17 replied to the thread Unable to delete template, missing linked clone?.Hi @Howard A2 Labs , Perhaps if you provide your VM and Storage configuration and state, that may help others to zoom in on the issue. qm config [vmid] pvesm status pvesm list [storage] cat /etc/pve/storage.cfg Depending on the storage type...
-
bbgeek17 replied to the thread Intermittent I/O errors on SAN-backed VM disks (Proxmox VE 9.2).Given your report that you have not found any IO related messages in "dmesg" and "journalctl" that is a pretty strong indication that the error is coming from a higher application layer. Blockbridge : Ultra low latency all-NVME shared storage...
-
bbgeek17 replied to the thread VM becomes unresponsive during Veeam backup.Hi @sudomaster.ljs , There have been multiple reports in the last few years of users experiencing similar issues with the combination of Veeam and PVE. Unfortunately I do not recall any of the reporters coming back with a concrete resolution...
-
bbgeek17 replied to the thread E1000E Not being initialized.Then your only option is to find a Kernel that works with the card. You may want to look into Ubuntu HWE Kernel. Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread E1000E Not being initialized.While I've seen some discussions around E1000e cards, I am not familiar with the issues personally. That said the solution could be as simple as replacing the card with a different brand, if possible. You could experiment with different Kernels...
-
bbgeek17 replied to the thread Intermittent I/O errors on SAN-backed VM disks (Proxmox VE 9.2).I am not familiar with how Bacula integrates with PVE. If it operates through the QEMU layer, similar to PBS and Veeam, it is possible that the I/O error originates at a higher layer than FC, multipath, or LVM - that is, within the QEMU layer...
-
bbgeek17 replied to the thread Determine the actual vm/clone creation date.You could also introduce a date indicating tag into your clone process, or export the log to central logging server to preserve the information for as long as you want to. Blockbridge : Ultra low latency all-NVME shared storage for Proxmox -...
-
bbgeek17 replied to the thread [SOLVED] Can't see the assigned pool.That said, your user is missing VM.Audit permission that allows the user to get listing of VMs. Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox
-
bbgeek17 replied to the thread [SOLVED] Can't see the assigned pool.Thank you for providing the info but its not in the format that is friendly to reading. Possibly because you lost the opening tag. If you look at the text-toolbox of the post/reply you will see an icon </> that will help you to get text into a...