Recent content by andrema2

I just uninstall the driver and let the update happen. Once it did I was expecting the disconnections I was seeing before. They did not appeared so far. I can confirm I'm using the r8169 driver instead of the r8168 that I was using before. In my case it seems that the issue is solved

Hi, I tried to update my proxmox servers. Two of them went ok without a problem. One of them I'm getting this error message Setting up proxmox-kernel-6.5.11-3-pve (6.5.11-3) ... Examining /etc/kernel/postinst.d. run-parts: executing /etc/kernel/postinst.d/dkms 6.5.11-3-pve...

So, I was able to figure this out. I had to install the r8168-dkms to make it work properly. Looks like the r8169 or something wasn't 100% compatible. Once I installed it the performance went back to the normal. Not sure if it will be ever fixed on the newer driver

I have checked the usb config, changed the usb port , changed the cables etc. My line of thought is, if it can download at 350mbps it shouldn’t be any hw issue nor the cable or port. It kind of proved that it can handle higher speeds. My thoughts are now with the Realtek drivers. The old...

So, this is a weird situation. I have a virtualized OpnSense under Proxmox. In fact they are two acting as HA. Last week I had a hardware failure on the main Proxmox hw and had to change the hardware. I returned the backuped VM on the new HW and it appeared to be fine. When I checked the...

Have you done it ? Did it work ?

I'm seeing the same thing

I did a test with 32 Gb and it took 28s instead of the 3 min it normally takes. On the other hand I have another VM with 256Gb of RAM that takes 5s to start. So my guess is, is the memory plus the HBA passthrough. I think this is the time it takes and I just have to get over it... I don't...

I didn't nor the NUMA was enabled. I enabled both. The boot time still the same. Anyway, it was a good tip the NUMA

Hi I have a TrueNas Core 13.0-U3.1 VM running under Proxmox 7.3.6. The boot time for that VM is really high. It doesn't happen for other VMs on the same server. This is what I see: after the start of the VM it takes up to two or more minutes to be able to see anything at the console. The whole...

Oi Oguz, To be honest I gave up and went in a different direction to solve my issue. Turns out that the specific WIFI module that I was using doesn't have drivers for linux in general. Some people tried to generate one compiling others drivers. The result is a very poor performance and a...

Thanks, was the reboot that was missing. I could swear that I've done it. Silly mistake....

Hi I have 3 nodes in my lab. Two of them have Linux 5.15.35-1-pve #1 SMP PVE 5.15.35-3 as their kernel. The other one have Linux 5.15.35-1-pve #1 SMP PVE 5.15.35-2 I have checked the source list on all machines and they are the same. The two that have the same versions are NUC PCs with i7...

Hi, I need to use a WIFI adapter on one of my VMs to be able to access an specific equipment. If I connect the usb wifi adapter, although the NICs are connected as before, I cannot access the server or ping it. As soon as I remove the adapter and reboot again, everything works. I think I...

Hi I'm trying to prune running proxmox-backup-client prune vm/105 --keep-hourly 25 --keep-daily 8 --keep-weekly 2 --keep-monthly 1 and this is the error I'm getting Error: unable to get (default) repository My backup per the GUI runs at 01:45 am, but I have a local job at the VE host that...