Recent content by Ahmet Bas

  1. A

    Snapshot function does not clean up properly?

    Exactly, but the disk image is now around 800GB and the actual data is < 200GB. Everytime snapshot fails it increases
  2. A

    Snapshot function does not clean up properly?

    Yes, but this will only remove the left over of "Voorderename" and not the other failed snapshot right?
  3. A

    Snapshot function does not clean up properly?

    Is there a way to remove the disk snapshot? To reclaim the unused disk, there is a way to remove the disk and restore from the backup but this is not a preferred way to remove the snapshot from the disk.
  4. A

    Snapshot function does not clean up properly?

    Thanks for the info, will this remove all leftovers since after every snapshot fails the disk usage gets bigger and bigger? We have similar setups where we don't have this issue only on a few of the servers. So in our case, if I understand it right, disable freeze will not work...
  5. A

    Virtual Machines freeze just after a live migration

    If I'm not wrong there was indeed an issue with the kernel 5.15 regarding hot migrations.
  6. A

    Snapshot function does not clean up properly?

    I found this thread: https://forum.proxmox.com/threads/snapshot-function-does-not-clean-up-properly.121840/ but no solution for me there.
  7. A

    Snapshot function does not clean up properly?

    Hello, I came acros a strange issue. One few servers we are unable to create or delete snapshot. In most cases snapshots work but the deletion makes the VM unvailble until the server gets a hard reset. Below some info VM config agent: 1,fstrim_cloned_disks=1 boot: order=scsi0 cores: 4 cpu...
  8. A

    Proxmox Start/Shutdown order

    But VM 300 should be turned of first then VM 200 and VM 100 should be turned off last in order ? But if I change the "Start/Shutdown order: 1" will VM 100 not be turned off first due to the start/shutdown order?
  9. A

    Proxmox Start/Shutdown order

    In Proxmox you can use VM -> Options -> Start/Shutdown order we you can configure the following values: Start/Shutdown order: Startup delay: Shutdown timeout: We have three VMs: VM 100 VM 200 VM 300 The shutdown should be done from VM 300, VM 200, and VM 100 and when it starts it should...
  10. A

    How to backup the hypervisor (pve)

    Thanks for the quick reply, are there any restore steps ? Or can I overwrite it once a fresh install is done?
  11. A

    How to backup the hypervisor (pve)

    Is there a documentation how to backup and restore the hypervisor?
  12. A

    Proxmox ZFS pool

    Thx, the firmware is updated but I keep receiving the same logs in dmesg.
  13. A

    Proxmox ZFS pool

    Thanks for bringing this to my attention. It's changed to 6.2 Is this issue resolved in 6.2? Since i'm unable to update the firmware: > Solidigm : This drive is no longer supported.
  14. A

    Proxmox ZFS pool

    Hello, I'm currently configuring a new Proxmox hypervisor with the following setup: 2x 1TB NVMe drives in RAID1 ZFS 8x 8TB NVMe drives in RAID10 ZFS The 8TB NVMe drives we are using: Intel DC4510 Series In dmesg I see the following lines: [Wed Apr 19 16:42:44 2023] nvme nvme0: I/O 321 QID...
  15. A

    Slow in PVE REALM login.

    We have the same issue with +- 800 ACLs. pveum acl list --output-format yaml | grep path | wc -l 798 When we check the time for ticket and user we get those values: #time pvesh create /access/ticket real 0m1.683s user 0m1.505s sys 0m0.169s #time pveum user permissions...

About

The Proxmox community has been around for many years and offers help and support for Proxmox VE, Proxmox Backup Server, and Proxmox Mail Gateway.
We think our community is one of the best thanks to people like you!

Get your subscription!

The Proxmox team works very hard to make sure you are running the best software and getting stable updates and security enhancements, as well as quick enterprise support. Tens of thousands of happy customers have a Proxmox subscription. Get yours easily in our online shop.

Buy now!