Would a Ryzen 4300U mini PC with 16GB RAM be enough for a small Proxmox VE lab?

oliviagarcia

New Member
Nov 15, 2026
6
0
1
I am planning a small home lab in my Madison apartment and space is tight, so I am looking at a compact mini PC rather than a rack server. The one I keep coming back to has a Ryzen 4300U, 16GB of RAM, and room for one M.2 drive. My goal is Proxmox VE with two or three lightweight VMs plus a container or two, mostly for learning and a small file share.

What I am unsure about is the network side, since it looks like a single Ethernet port, and whether 16GB is enough once ZFS takes its share of memory. I also wonder whether the CPU will feel constrained if I add a VM with heavier I/O. I found this specification online and have no hands-on time with it.

Has anyone here run Proxmox VE on a similar low-power mini PC? I would appreciate thoughts on RAM sizing, ZFS versus ext4, and whether the single NIC became a problem.

Update after looking around more - KAMRUI Pinova P1 Mini PC Review kept coming up for the 4300U specs. I am still unsure whether 16GB leaves enough headroom with ZFS, but I am leaning toward ext4 and maybe a USB NIC for a second interface.
 
Last edited:
If you plan to build a Proxmox VE cluster in the future, having only one Ethernet port could be a limitation.

A dedicated network for Corosync is not strictly required, but separating cluster communication from other network traffic is recommended for stability.

If you only plan to use a single Proxmox VE node, however, one Ethernet port should be sufficient for your current needs.
 
On a single (homelab) node, one NIC is not a deal-breaker.
16GB RAM depends on your LXC/VM needs - as you will have approx. 14GB available.
BUT: The one single M.2 drive in my opinion is an issue. It is a SPOF & on a (cheap) mini-PC this can fail (both the drive itself & the IO on the bus). You should look for a mini-PC that can house at least one other drive, so that you have backups stored elsewhere. (USB-attached drives can be flaky).
On a mini-PC, the 321 backup policy is crucial - expect to have to reinstall EVRYTHING at some point!
 
Look for a used Dell Optiplex Micro on Ebay. In this you can use 2 x M.2, you can expand the Mem and you will get at least with a 10th Gen i3 4+4 Cores.

You will have a lot of trouble with this unidentifyable China-Scrum.
 
  • Like
Reactions: news
That CPU is very capable. You will run out of RAM long before you over tax the CPU. 16GB is not going to be enough in my opinion. For a lab environment, one drive is a risk, but it is an acceptable risk if this is a testing environment and you can tolerate potentially losing data in a drive failure. Two drives in a mirror would be better. Single NIC doesn't bother me. I would go ZFS personally.
 
Of course everybody has a slightly different recommendation for you. My two most important cents are these:

1) always use ZFS. The idea of "ZFS eats my RAM" was an urban legend from the beginning and you would lose a lot of really great features: https://forum.proxmox.com/threads/f...y-a-few-disks-should-i-use-zfs-at-all.160037/

2) buy more RAM - even with today's crazy prices. RAM is always the resource which limits adding more VMs/Containers. ((I have suspended some machines with "only" 64 GiB Ram and got me some with 128 GiB RAM. In my Homelab. Admitting that was before the current... problem.))

Again: everyones mileage will vary...
 
  • Like
Reactions: news
always use ZFS
On a single-node cheap mini-PC, I think ZFS is a no-no. Except for the extra data writing involved on some crummy disk (consumer standard or below), while using an inferior bus, & some suspicious RAM, doing ZFS on a single disk without redundancy, does not make sense to me. I know my comment will probably start the whole ZFS yes/no convo going, compression, bit-rot & snapshotting, but I stand by my opinion; ZFS is a super & powerful engine, put it in an applicable car.
 
  • Like
Reactions: GMBauer
  • Like
Reactions: gfngfn256