Latest activity
-
UdoB reacted to lucavornheder's post in the thread Configering a Cluster with only one node (first) with
Like.
Hi, yes, this is absolutely possible. I would do it the same way. -
UdoB replied to the thread Configering a Cluster with only one node (first).Sure! To check some aspects, usual problems and possible showstoppers read this forum ;-) and those wiki pages: https://pve.proxmox.com/wiki/Migrate_to_Proxmox_VE https://pve.proxmox.com/wiki/Advanced_Migration_Techniques_to_Proxmox_VE Good...
-
RolandK replied to the thread Opt-in Linux 7.0 Kernel for Proxmox VE 9 available.also getting these. have opened https://bugzilla.proxmox.com/show_bug.cgi?id=7585 for it -
Wwagnbeu0 replied to the thread e1000e eno1: Detected Hardware Unit Hang:.@celemine1gig Thank you for the update. I know that this problem occurs primarily with INtel NIC, but as ou can see it happens again and again - so this is why I am also looking for a permanent solution even if I have no Intel NIC. Maybe the...
-
SteveITS replied to the thread CEPH cluster_network defaults to a single node IP rather than to a subnet.AFAIK that’s normal in PVE. And equal? -
fiona replied to the thread Live Migrations get slower over time.Hi, please share the VM configuration of an affected VM qm config ID with the numerical ID of the VM as well as the output of pveversion -v and full system journal from the source and target node from the boot until and including the problematic... -
YaZoal replied to the thread Unexpected reboot.Is this node in a cluster? Please share journalctl log include ~4 before the reboot observed, for example: root@pve ~# journalctl --since "2026-05-09 00:00" --until "2026-05-09 12:00" | gzip > /tmp/$(hostname)-syslog.txt.gz For a cluster, it is... -
Ssachinh replied to the thread proxmox (VSphere VMWare to Proxmox migration).Thanks for reply. Hostbus change is what very obvious thing to try. As same problem was resolved with new Linux Version i.e. by changing the Hostbus to IDE as I mentioned in my first post. But that solution is not working here anymore. Actually...
-
Mmkevenaar replied to the thread Proxmox with 48 nodes.3 nodes (HPE DL360 Gen10) On-board 1GE link to oob/mgmt switch for "link 0". 2 2-port 25/10GE NICs with 1 port each in an LACP (802.3ad) bonding to Nexus switches (in a VPC setup) with 10GE DAC cables 802.1q. "link 1" is running on an SDN VLAN...
-
TWe are currently setting up two separate PVE clusters. Both are HCI clusters running Ceph. The servers are distributed across two colocation facilities in the same city, connected via a low-latency data centre interconnect. One cluster consists...
-
mariol replied to the thread [SOLVED] Super slow, timeout, and VM stuck while backing up, after updated to PVE 9.1.1 and PBS 4.0.20.Kernel 7.0.0-3-pve is also working fine with this -
Llucavornheder replied to the thread Configering a Cluster with only one node (first).Hi, yes, this is absolutely possible. I would do it the same way.
-
Uuzumo reacted to Scivaro's post in the thread GMKTec NucBox K11 - AMD 8945HS / 780M Windows 11 VM GPU Passthrough with Like.
[SOLVED] GMKtec NucBox K11 / AMD 8945HS 780M GPU Passthrough — Complete Working Solution After extensive debugging I got full AMD Radeon 780M (Phoenix3, 1002:1900) passthrough working on Proxmox 9.1.9 — including surviving Windows restarts...
-
Ppbliedung posted the thread Configering a Cluster with only one node (first) in Proxmox VE: Installation and configuration.Hello everybody, I would like to know if configering a cluster with only one node and attached storage is possible. The problem: One of my customers would like ot migrate from one hypervisor to proxmox. They need to keep their current hosts...
-
CChimKenda replied to the thread Lattepanda Sigma Intel Raptor Lake iGPU Passthrough.Huhu, danke für euren Input, ich hab den Post mal angepasst damit man es besser lesen kann ;) Ich hab das mit den erweiterten Funktionen ausprobiert und auch das mit der ROMbar, sowie das ich die GPU auf Primary setze und die anzeige auf "none"...
-
Mmunchworker reacted to Upstairs_Cycle384's post in the thread [SOLVED] Trying to enable nested virtualization results in perfomance loss on vm with Like.
You are missing three things: 1. Hyper-V enlightenments enabled. Enable as many as you can that are performance driven 2. MBEC support enabled. This is most critical. Your processor supports it but you are not exposing that to the guest 3. A...
-
Mmunchworker replied to the thread [SOLVED] Trying to enable nested virtualization results in perfomance loss on vm.1. I will check Hyper-V enlightenments out 2. MBEC needs exposing, i will test this and post an update 3. For this I need to check if the nvidia vGPU drivers are already supporting this kernel.
-
UdoB reacted to Martin.B.'s post in the thread [SOLVED] cannot take snapshot: local ZFS uses raw for vdisks / cannot change to qcow with Like.
Thanks you all for the fast comments. I could not start a snapshot in the GUI, the button "Take snapshot" was greyed out every time i tried. The problem was, as often, sitting in front of the keyboard.... and now i feel really bad. I just...
-
Mmunchworker reacted to Impact's post in the thread [SOLVED] Trying to enable nested virtualization results in perfomance loss on vm with Like.
There's a few discussions about this like this: https://forum.proxmox.com/threads/the-reasons-for-poor-performance-of-windows-when-the-cpu-type-is-host.163114/
-
Mmunchworker replied to the thread [SOLVED] Trying to enable nested virtualization results in perfomance loss on vm.Thank you for your input, the host has 2 xeon processors which amounts to a total of 112 cores. 16 Cores for every machine would be a bit much current setup is 12 cores and the one shown hast 16 cores for testing. Furthermore the VMs are used as...