Latest activity
-
UdoB reacted to Johannes S's post in the thread Help with Network Configuration for first time user with
Like.
You can also run the qdevice as vm or container on the PBS if you install a PVE and PBS on the same host without adding it to the cluster: https://forum.proxmox.com/threads/2-node-ha-cluster.102781/#post-442601 In the case of the OP I would go... -
Vvesuvienne posted the thread Disk speed: VM Freebsd 15 vs Debian Trixie - Proxmox in Proxmox VE: Installation and configuration.Hi team, Just dropping some result of disk speed performance, if someone have some time, knowledge or any clues(maybe i did something wrong) to upgrade my freebsd 15 disk speed: Proxmox - LVM-Thin - VM - CPU:2 MEMORY:2GB - VM disk mounted...
-
AAmstellodamois posted the thread Download speed brutally reduced in Proxmox VE: Networking and Firewall.Hey all, please be patient: I'm an absolute noob, I don't know what I'm doing :) Since yesterday, the download speed of my Proxmox VE 8.4.18 node ('cause I still have 900 Mb/s on my other equipments, including on the switch where the node is...
-
-
KKingneutron reacted to proxuser77's post in the thread How to install and use qm from remote host? with Like.
qm is a local command-line tool. It is installed on the Proxmox host itself and not exposed as a network service. To use it, you need to log in to the Proxmox host, usually via SSH, and run the command there, just as you would with any other...
-
As others have mentioned, it is technically possible to set size=2 and min_size=1, but it does come with risks. From a Proxmox and Ceph perspective, this configuration is not recommended. While it may not be explicitly unsupported, the fact that... -
I gathered some experience a year ago: https://forum.proxmox.com/threads/fabu-can-i-use-ceph-in-a-_very_-small-cluster.159671/ If I want a stable system I would never start with less than three copies and min=2.
-
TTrevorW replied to the thread [SOLVED] No /etc/kernel/proxmox-boot-uuids found, skipping ESP sync.Thanks UdoB I've unmounted /boot/efi and proxmox-boot-tool status says nothing of interest - it just takes me back to no boot uuids existing. root@Proxb2:~# umount /dev/sda2 root@Proxb2:~# proxmox-boot-tool status Re-executing...
-
-
Aalexskysilk replied to the thread First Proxmox homelab build - sanity check on hardware, service layout, and storage.When you say "mainstream advice" its good to note the background, reasoning, and authority of whoever you are quoting. In an enterprise environment with security policies, or on a dirty (shared) hypervisor the advice certainly applies- but its a...
-
Aalexskysilk replied to the thread First Proxmox homelab build - sanity check on hardware, service layout, and storage.Before answering the question (its really just the one) I encourage you to really consider the implications of an all docker workload. docker images are immutable and live in a repo; the only things you MIGHT want to keep a copy of is the...
-
VvedesreveR posted the thread UI-Anzeige im Repositories-Tab bei Verwendung vom Offline-Mirror in Proxmox VE (Deutsch/German).Hallo Zusammen, ich habe eine Feststellung in der UI Repository Anzeige gemacht, wenn Custom-Repos über die Offline-Mirror funktionalität verwendet werden: Obwohl funktionierende Repos eingetragen sind, wird trotzdem angezeigt, dass man keine...
-
JJohannes S replied to the thread Help with Network Configuration for first time user.You can also run the qdevice as vm or container on the PBS if you install a PVE and PBS on the same host without adding it to the cluster: https://forum.proxmox.com/threads/2-node-ha-cluster.102781/#post-442601 In the case of the OP I would go...
-
JJohannes S reacted to d.oishi's post in the thread Help with Network Configuration for first time user with Like.
Make sure not to forget to configure the migration network in the Datacenter options. https://pve.proxmox.com/pve-docs/pve-admin-guide.html#_options Although isolation is generally recommended, I have experience building a 2+1 cluster using PBS...
-
JJohannes S reacted to MarkusKo's post in the thread Help with Network Configuration for first time user with Like.
Better isolate it, create an additional minimal debian vm or debian container on your synology or use a raspberry pi. *edit* Depending on your requirements you could just run your PVE hosts standalone, not in a cluster, then you don't need a...
-
JJohannes S reacted to MarkusKo's post in the thread Help with Network Configuration for first time user with Like.
Looks good. Not sure if you need a LAG for Management, you could just assign a differnet subnet to each of the adapters, less complexity. Don't forget to add a qdevice or you will get issues with your 2 node cluster. And for PBS, it is...
-
JDas ist mir natürlich klar. Trotzdem finde ich es wichtig, diese an den Onlinepranger zu stellen. Kann nur von unserem Markt sprechen. Init7: statischer /48 Präfix, kein CG-NAT. Salt: Für 10Fr. im Monat wird die CG-NAT IPv4 eine echte IPv4...
-
JJohannes S reacted to alexskysilk's post in the thread First Proxmox homelab build - sanity check on hardware, service layout, and storage with Like.
You are asking a lot from a relatively modest host. its doable, but you'll need to temper your "performance" expectations. on that subject- That will multiply the "performance expectations issue" substantially. In addition, doing a passthrough...
-
JLooks like RDMA isn't actually being used for data - mr_used_count: 0 means SMB Direct's RDMA memory registration engine has never been used. The connection negotiated RDMA/SMBDirect successfully, but actual I/O is falling back to regular TCP...
-
Jjlgarnier replied to the thread [SOLVED] VM filesystem corrupted.Thanks @Onslow! That was a typo indeed... Can you please just clarify a few things: - If I boot from a disk rescue image, how can I determine what is the main filesystem, as it is not running? - Once "into the VM", how could I mount the...
-
Ggctwnl posted the thread Need some help recovering/rebuilding my pve+pbs home server in Proxmox VE: Installation and configuration.The controller of my SSD (Samsung 980 Pro...) died so I have to rebuild my setup from backups. The first step is to install PVE and on top of that PBS and update everything, then do my LUKS setup on my external RAID and recover /etc/pve from a...
-
BBenneffect replied to the thread VM /mnt Data Erroneously Landing on rpool.The problem isn't that the my directories aren't in the correct location - I've fixed that (I think). My problem is that rpool thinks it is full when I cannot find anything there.
