Latest activity
-
VvedesreveR posted the thread UI-Anzeige im Repositories-Tab bei Verwendung vom Offline-Mirror in Proxmox VE (Deutsch/German).Hallo Zusammen, ich habe eine Feststellung in der UI Repository Anzeige gemacht, wenn Custom-Repos über die Offline-Mirror funktionalität verwendet werden: Obwohl funktionierende Repos eingetragen sind, wird trotzdem angezeigt, dass man keine...
-
JJohannes S replied to the thread Help with Network Configuration for first time user.You can also run the qdevice as vm or container on the PBS if you install a PVE and PBS on the same host without adding it to the cluster: https://forum.proxmox.com/threads/2-node-ha-cluster.102781/#post-442601 In the case of the OP I would go...
-
JJohannes S reacted to d.oishi's post in the thread Help with Network Configuration for first time user with
Like.
Make sure not to forget to configure the migration network in the Datacenter options. https://pve.proxmox.com/pve-docs/pve-admin-guide.html#_options Although isolation is generally recommended, I have experience building a 2+1 cluster using PBS... -
JJohannes S reacted to MarkusKo's post in the thread Help with Network Configuration for first time user with Like.
Better isolate it, create an additional minimal debian vm or debian container on your synology or use a raspberry pi. *edit* Depending on your requirements you could just run your PVE hosts standalone, not in a cluster, then you don't need a...
-
JJohannes S reacted to MarkusKo's post in the thread Help with Network Configuration for first time user with Like.
Looks good. Not sure if you need a LAG for Management, you could just assign a differnet subnet to each of the adapters, less complexity. Don't forget to add a qdevice or you will get issues with your 2 node cluster. And for PBS, it is...
-
JDas ist mir natürlich klar. Trotzdem finde ich es wichtig, diese an den Onlinepranger zu stellen. Kann nur von unserem Markt sprechen. Init7: statischer /48 Präfix, kein CG-NAT. Salt: Für 10Fr. im Monat wird die CG-NAT IPv4 eine echte IPv4...
-
JJohannes S reacted to alexskysilk's post in the thread First Proxmox homelab build - sanity check on hardware, service layout, and storage with Like.
You are asking a lot from a relatively modest host. its doable, but you'll need to temper your "performance" expectations. on that subject- That will multiply the "performance expectations issue" substantially. In addition, doing a passthrough...
-
JLooks like RDMA isn't actually being used for data - mr_used_count: 0 means SMB Direct's RDMA memory registration engine has never been used. The connection negotiated RDMA/SMBDirect successfully, but actual I/O is falling back to regular TCP...
-
Jjlgarnier replied to the thread [SOLVED] VM filesystem corrupted.Thanks @Onslow! That was a typo indeed... Can you please just clarify a few things: - If I boot from a disk rescue image, how can I determine what is the main filesystem, as it is not running? - Once "into the VM", how could I mount the...
-
Ggctwnl posted the thread Need some help recovering/rebuilding my pve+pbs home server in Proxmox VE: Installation and configuration.The controller of my SSD (Samsung 980 Pro...) died so I have to rebuild my setup from backups. The first step is to install PVE and on top of that PBS and update everything, then do my LUKS setup on my external RAID and recover /etc/pve from a...
-
BBenneffect replied to the thread VM /mnt Data Erroneously Landing on rpool.The problem isn't that the my directories aren't in the correct location - I've fixed that (I think). My problem is that rpool thinks it is full when I cannot find anything there.
-
Dd.oishi replied to the thread Help with Network Configuration for first time user.Make sure not to forget to configure the migration network in the Datacenter options. https://pve.proxmox.com/pve-docs/pve-admin-guide.html#_options Although isolation is generally recommended, I have experience building a 2+1 cluster using PBS...
-
PPhyterJet reacted to jemme's post in the thread [TUTORIAL] FROM NOTHING: Physical disk with Windows 11 as VM + GPU pass-through with Like.
So there's a limit of 16384 characters, so this is split into two parts! Like promised, here's the output. IOMMU group 0 00:00.0 Host bridge [0600]: Intel Corporation 10th Gen Core Processor Host Bridge/DRAM Registers [8086:9b43] (rev 05) IOMMU...
-
PPhyterJet reacted to jemme's post in the thread [TUTORIAL] FROM NOTHING: Physical disk with Windows 11 as VM + GPU pass-through with Like.
Hello! This is my first time starting a thread on here, but I've posted on an already existing thread about my problem. Since I've solved it and now have a running Windows 11 VM that operates as a "normal computer", I thought I would share my...
-
Ppsalkiewicz posted the thread [PROJECT] Proxmox PVE & Atlassian Confluence integration in Proxmox VE: Installation and configuration.Hello Community, I'd like to share one of my projects with you. It's a python tool that connects to Proxmox PVE API and gets a list of virtual machines. It creates a table with virtual machine details and converts it into page template for...
-
-
GGold007 reacted to 0x2c4's post in the thread [SOLVED] How to remove LVM-thin and then expand local with Like.
WOW, three lines of code, and the job is done: lvremove /dev/pve/data lvresize -l +100%FREE /dev/pve/root resize2fs /dev/mapper/pve-root Massive THANK YOU :)
-
PPhyterJet replied to the thread [TUTORIAL] FROM NOTHING: Physical disk with Windows 11 as VM + GPU pass-through.I registered an account just to thank you for this writeup. A few things. Works with Proxmox 9.1 (AMD 5700G, Nvidia RTX 4060) Thankfully, I needn't mess with IOMMU groups Installed on an empty drive. Machine can also boot directly from that...
-
UUpstairs_Cycle384 replied to the thread Random IO Error - Windows Server 2025.We are seeing this problem randomly (maybe once every few months or so) on our systems as well. VM fails with `io-error` and has to be powered off. Similar to OP: We have a ZFS directory with qcow2 images on them. Many TBs of space available. No...
-
Kkwinz reacted to Nemesiz's post in the thread Ceph 20.2 Tentacle Release Available as test preview and Ceph 18.2 Reef soon to be fully EOL with Like.
I`m tracking Ceph mailing list and from it I assume developers leaves testing stage to customers. Safe upgrade should be done to X.Y.2+ version only.
-
Ffrankz posted the thread error smart on disk SDA but from gui not confirm this . in Proxmox VE: Installation and configuration.I have a log interpretation problem that is causing me confusion. I constantly receive the following alarm from the service smartd: This message was generated by the smartd daemon running on: host name: pve3 DNS domain: internal2.lan...
-
