Latest activity
-
NNemesiz replied to the thread High latency on proxmox ceph cluster.Try to turn off write cache.
-
Vviruslab replied to the thread Proxmox randomly reboots while doing backup job.My Proxmox node reboots during backup once a month or two. No errors in kernel or journal Sometimes warning about memory pressure, but ram mostly occupied by zfs.
-
Vviruslab replied to the thread Host reboots during backups.My Proxmox node reboots during backup once a month or two. No errors in kernel or journal Sometimes warning about memory pressure, but ram mostly occupied by zfs.
-
Bb0nef1sh replied to the thread Unexpected Reboots on current Kernel.i installed and pinned that kernel, still getting reboots sadly, maybe it is hardware after all
-
JDas passiert bei CTs leider üblicherweise nicht. Zumindestens nicht vor Beendigung. Bitte nicht. Snapshots ersetzen ein richtiges Backup genau so wenig wie RAID. Ich empfehle immer beides. Schau dir auch mal cv4pve-autosnap an Schau auch mal den...
-
JJohannes S reacted to garfield2008's post in the thread merkwürtiges Netzwerkproblem beim Zugriff auf PVE with
Like.
Ich glaub ich habe die Lösung. Habe gerade mal bei der VM die MTU auf 1500 begrenzt und siehe da, ich komme mit allen Protokollen auf alle PVE/PBS. Bleibt also die Frage, was hat sich vor einem halben Jahr geändert? -
JJohannes S reacted to deimosian's post in the thread enable CONFIG_RUST for Proxmox kernel with Like.
Then the next thread will be asking how to disable it.
-
Ffreaknils posted the thread High latency on proxmox ceph cluster in Proxmox VE: Installation and configuration.Hi there, we are running an Proxmoy PVE Ceph cluster. Current configuration is: 3 Nodes Each 2 x 10GBit/s LACP to 4 switches (only for ceph) 2 x Intel Xeon E5-2640 2,6GHzs 192GB RAM Each 5 Crucial SATA SSD CT2000MX500SSD1 on HBA But currently...
-
-
JJohannes S reacted to alexskysilk's post in the thread Pardon my less-than-intelligent question, but is there a way to install Proxmox on a Ceph cluster? with Like.
"lower" and "higher" are subjective. Ceph achieves HA using raw capacity. suit yourself. this is not a recommended deployment. You are far better served by just having two SEPERATE VMs each serving all those functions without any ceph at all-...
-
UdoB reacted to garfield2008's post in the thread merkwürtiges Netzwerkproblem beim Zugriff auf PVE with Like.
Ich glaub ich habe die Lösung. Habe gerade mal bei der VM die MTU auf 1500 begrenzt und siehe da, ich komme mit allen Protokollen auf alle PVE/PBS. Bleibt also die Frage, was hat sich vor einem halben Jahr geändert? -
UdoB reacted to Bu66as's post in the thread merkwürtiges Netzwerkproblem beim Zugriff auf PVE with Like.
@garfield2008, Der tcpdump verrät es: Der TCP-Handshake klappt einwandfrei (SYN → SYN-ACK → ACK), aber danach kommt keine Daten-Übertragung zustande — der Server schickt nach 5 Sekunden ein FIN. Das ist ein klassisches MTU-Problem. Schau dir...
-
Cchamathjayasekara5962@gma posted the thread Setting up talos linux on phoenixNap BMC proxmox as a guest os. in Proxmox VE: Networking and Firewall.Is it possible to get any help from anyone?, I'm so lost in setting up any guest os in proxmox ve in phoenixNap BMC.
-
Jjaminmc replied to the thread Upgrade to firmware-linux 20260110.Installing the test repository provides access to pve-firmware version 3.18-1, built on firmware-linux 20260110, along with the newer proxmox-kernel-6.17.13-1-pve, which may meet your needs.
-
Aalia80 replied to the thread [SOLVED] Proxmox VE update to 9.1.5, now the network card is slow.Additional info: lspci | grep -i ethernet 01:00.0 Ethernet controller: Broadcom Inc. and subsidiaries NetXtreme BCM5720 Gigabit Ethernet PCIe 01:00.1 Ethernet controller: Broadcom Inc. and subsidiaries NetXtreme BCM5720 Gigabit Ethernet PCIe...
-
Aalia80 posted the thread [SOLVED] Proxmox VE update to 9.1.5, now the network card is slow in Proxmox VE: Networking and Firewall.Hello, I recently did an in place upgrade to PVE 9, everything seems to be working fine but now the network card seems to be slow. I run pfSense in a VM with a couple of network interfaces passed through. I have not made any changes to the VM...
-
Ddeimosian replied to the thread enable CONFIG_RUST for Proxmox kernel.Then the next thread will be asking how to disable it.
-
Jjustlikeef replied to the thread Upgrade to firmware-linux 20260110.Sorry, that was a mistype on my part. The kernel version is fine, it's the firmware version that is problematic...
-
Jjaminmc replied to the thread Upgrade to firmware-linux 20260110.Strix appears to require a more recent kernel. One user reported that My Proxmox 6.19.1 pve test kernel works well for them—this version is available for testing at...
-
Jjaminmc replied to the thread enable CONFIG_RUST for Proxmox kernel.The Proxmox kernel is based on Ubuntu’s kernel. Since Ubuntu’s kernel version 6.19 includes CONFIG_RUST enabled by default, and unless the Proxmox team explicitly disables it in their next major release, CONFIG_RUST should remain enabled. As a...
-
Jjaminmc replied to the thread [TUTORIAL] Custom Proxmox 6.19.0 Kernel. 6.18.0 is also available for Testing..I'm glad I could help! Every few days, I check for a newer kernel at the Ubuntu kernel repository on Launchpad, then pull and compile it with the Proxmox magic. If it works, I update my GitHub. It looks like you have the latest version — so far...
