Latest activity
-
bbgeek17 replied to the thread Cannot access web GUI at all.If the pool ends at 249, then 240 is within the range. Pick an IP that is higher than 249 Blockbridge : Ultra low latency all-NVME shared storage for Proxmox - https://www.blockbridge.com/proxmox -
CChrisBozeman reacted to RoCE-geek's post in the thread High VM-EXIT and Host CPU usage on idle with Windows Server 2025 with
Like.
I'm afraid that I've already expressed all the key points or relevant ideas I had so far, so I've no need to repeat it. To be clear, I'm not saying that this is a KVM/QEMU/Proxmox problem, I'm just in the gang of those saying "look, something bad... -
CChrisBozeman reacted to RoCE-geek's post in the thread High VM-EXIT and Host CPU usage on idle with Windows Server 2025 with Like.
And here is the root of "misunderstanding". Most of the contributors here are looking for the 24H2 side-effects mitigation, simply because a 3x increase of idle load is hardly acceptable for us, and we do not want to resign ourselves to the fact...
-
MMrt12 replied to the thread Proxmox LXC mount point permissions.I see, I see. I did not realise that this is a problem with the package but instead was thinking the problem comes from my config that must be wrong in some way. Thanks! I prefer, however, not to use the test repo. I think I can wait until the...
-
HHope replied to the thread Ich benötige eure HILFE / ZFS pool ist weg..Danke Dir trotzdem für deine Hilfe. Ich hoffe es kann mir jemand weiterhelfen. Gruß Hope
-
Cchazwolf_ replied to the thread Cannot access web GUI at all.I did not, DHCP pool ends at ...249, both the PC (and MacBook) and server are within the range.
-
Cchazwolf_ replied to the thread Cannot access web GUI at all.http or https, doesnt work
-
G_gabriel replied to the thread Cannot access web GUI at all.don't forget httpS://ip:8006/
-
CHello, I set up Proxmox on a computer yesterday and got most of the configuration I needed done. However, coming back today I cannot access the web GUI at all. I tried to connect via the IPv4 address it gives, yet it times out. I was able to...
-
-
UdoB replied to the thread Ich benötige eure HILFE / ZFS pool ist weg..Sorry, ich habe noch nie OMV auf PVE verwendet und ich habe auch noch nie einen ganzen ZFS Pool in eine VM hineingereicht... -
HHope replied to the thread Ich benötige eure HILFE / ZFS pool ist weg..@admin: SORRY falsches Forum. Bitte ins "Proxmox VE (Deutsch/German)" verschieben. Danke.
-
Ssacarias replied to the thread Bug report from 2024-04-22.@t.lamprecht : Already post it as a bug report and it got rejected for no reason.
-
Cchristian.hahn replied to the thread Proxmox crashes with Kernel Error.i think i had to exchange ram and flash latest bios
-
Mmatesxs replied to the thread Proxmox crashes with Kernel Error.Hi, have similar problem. The server was running without problems for like 2 years and now just started doing the same thing described in on the top What was the solution for this problem?
-
Da Falk leider den Link zu seiner Methode für minimale Downtime vergessen hat: https://pve.proxmox.com/wiki/Migrate_to_Proxmox_VE#Attach_Disk_&_Move_Disk_(minimal_downtime) Dazu hat er auch mal einen Vortrag gehalten... -
powersupport replied to the thread Raid1 boot array, drive replacement procedure.Replacing a Failed Disk in Proxmox (BTRFS RAID1 – Simple Explanation) If one disk fails in a Proxmox BTRFS RAID1 setup, your server will still boot from the other disk. That’s normal and expected. Sometimes it boots in “read-only mode.” This is... -
Aalpha754293 replied to the thread Pardon my less-than-intelligent question, but is there a way to install Proxmox on a Ceph cluster?.I don't understand where you guys are getting this idea from. As shown above, with the system that has four nodes where each node has six 3.5" HDD bays, as long as those four nodes presents the six HDDs as OSDs per node, then I get 24 OSDs with...
-
HHope replied to the thread Ich benötige eure HILFE / ZFS pool ist weg..Hallo Udo, leider komme ich überhaupt nicht weiter. Das mit dem PlugIn in OMV hat keine Verbesserung gebracht. Was ich erreichen möchte ist das ich den ZFS Pool an OMV durchreichen kann: Jedoch habe ich scheinbar einen "neuen" erstellt...
-
-
JJohannes S reacted to _gabriel's post in the thread yawgpp (Yet Another Windows Guest Performance Post) with Like.
aes is already in x86-64-v3 hv* args are already applied when guest os type is set to Windows
-
JJohannes S reacted to alexskysilk's post in the thread yawgpp (Yet Another Windows Guest Performance Post) with Like.
ahhhh that makes so much sense... I so rarely set up windows guests so I didnt even think of that.
