Latest activity
-
Falk R. replied to the thread 10Gb Netzwerk erreicht nur 1Gb Geschwindigkeit.Du könntest mal mit mehreren Threads versuchen, falls die CPU bremst. Einfach den Schalter -P 8 für 8 Threads testen. Wenn das nichts bringt, liegt das irgendwo im Netzwerk. Eventuell mal zum testen direkt zusammenstecken. -
MMHeymann replied to the thread 10Gb Netzwerk erreicht nur 1Gb Geschwindigkeit.Accepted connection from 192.168.2.10, port 52613 [ 5] local 192.168.2.200 port 5201 connected to 192.168.2.10 port 52614 [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 135 MBytes 1.13 Gbits/sec [ 5]...
-
cheiss replied to the thread [SOLVED] How to re-enable networking when moving boot disk to new hardware?.Drivers are normally loaded automatically by the kernel based on detected PCI IDs. Most likely the interface name is different - each hardware/firmware combination tends to enumerate PCI devices in a different order and manufacturers place... -
Ddextro reacted to Roger Mangraviti's post in the thread [TUTORIAL] How to run Proxmox VE as a tmpfs memory resident operating system with
Like.
Dear Proxmox Community, openQRM would like to announce the new openQRM Community version 5.3.50 which now supports Proxmox VE 7.0 running as a tmpfs memory resident operating system. This allows compute nodes, physical and virtual servers to... -
Ffanhed replied to the thread Passthrough RTX 6000/5090 CPU Soft BUG lockup, D3cold to D0, after guest shutdown.Finally, I simply solved my problem using your method.
-
FFearless-Grape5584 replied to the thread PVE 9.0.11: pool-based RBAC – GUI shows "Permission check failed (/vms/101, VM.Audit)" after successful VM delete.Thanks for your reply and for taking the time to look into this. Regarding your question about the two checkboxes in the Destroy dialog: [x] Purge from job configurations [x] Destroy unreferenced disks owned by guest In my original test, I...
-
Ggctwnl posted the thread [SOLVED] How to re-enable networking when moving boot disk to new hardware? in Proxmox VE: Installation and configuration.I have moved my boot and data disks from an Intel NUC 10th generation to an ASUS NUC 13th generation. This works for now, except for one essential thing: networking. I suspect that as PVE was installed on different ethernet hardware, it might be...
-
Jjanus57 replied to the thread CPU Hot plug not working even after making all steps from the docs.Hi, Have you ADD the "UDEV rule" inside your VM (see on the wiki page) ? Have you ADD the Hotplug in the "options" menu of that VM ? Best regards,
-
Bbeisser replied to the thread GMKTEC K12 | Ryzen 7 H 255 | Problem with IGPU.i have uploaded my vbios and rom file for the h255 to https://cloud.catacombs.de/s/5JRq7JLSz92zmGk so far i have only figured out that hdmi output works when i disable the graphics card in the device manager, but not with it disabled.
-
news replied to the thread ZFS-ERROR Live-Migration: cannot create snapshot: out of space.You have a nvme-2tb/vm-130-disk-1 "Disk", this is a zfs volume witch use: "referenced 443G". Then with this zfs snapshot nvme-2tb/vm-130-disk-1@__replicate_130-0_1766276210__ it will use: "referenced 443G". In toal, with all additional zfs... -
Wwire2hire replied to the thread Proxmox Datacenter Manager 1.0 (stable).in the acme options the propogation time are different from the pve options. Example netcup need 600, only 48 can be set. so acme certs with netcup dont work .
-
Ffanhed reacted to chaosgrid's post in the thread Passthrough RTX 6000/5090 CPU Soft BUG lockup, D3cold to D0, after guest shutdown with Like.
hey guys, I have a confirmed fix for the RTX PRO 6000 Max-Q and the CPU soft lock bug / GPU reset failure with error messages like not ready 32767ms after FLR; waiting I managed to successfully shut down and restart the VM and the GPUs still...
-
Falk R. replied to the thread Nach Reboot keine VMs und LXCs.Da du sicher Backups hast, kannst du dir auch die Konfiguration des jeweiligen Backups anzeigen lassen.
-
Falk R. replied to the thread 10Gb Netzwerk erreicht nur 1Gb Geschwindigkeit.Bei 160MB/s ist es ja schon mal mehr als 1 GBit. Was kommt mit iperf raus? Wie ist dein Netzwerksetup, wenn du zwei Bridges hast? Wenn du auf beiden Bridges das selbe Subnetz verwendest, antwortet der Server vermutlich auf der 2,5G Karte.
-
MMHeymann replied to the thread 10Gb Netzwerk erreicht nur 1Gb Geschwindigkeit.Moin, Ich habe die Geschwindigkeit mit iperf3 und PingTool getestet. Außerdem habe ich eine Große Datei auf das NAS kopiert (magere 160MB/s).
-
DDeviC3 posted the thread CPU Hot plug not working even after making all steps from the docs in Proxmox VE: Installation and configuration.Hi, problem as in topic. I have installed PVE on bare metal (version 9.01). I wanted to have a way to change CPU (and then also memory) parameters on go while Linux server is running. If I understood correctly from here...
-
MMarkusKo replied to the thread Proxmox in a US Federal environment?.I you are concerend about encryption you can use your server hardware for that. As an example, on HPE Servers with SED Drives you can encrypt all your drives within the BIOS (Direct Attached NVMe) or on the RAID Controller setup. They are...
-
PPatrick P replied to the thread Qnap VirtStaion PBS Restore Abbruch.Haben das problem gelöst. Es Lag am Netzwerk, wie es im Log Steht. Irgendein Config Fehler in der Unifi Umgebung. Haben ein Seperates Netzwerk via USB Netzwerkkarte am PVE und den 2ten Port vom Qnap gemacht und alles Lief ohne Fehler durch.
-
Xxenon96 replied to the thread pvestatd crashes every few days.My issue went away by moving back my iGPU-Passthrough to a NVIDIA-Passthroungh to my Plex VM. Maybe the issue itself Game from the strongtz/i915-sriov-dkms By disabling the driver everything works Fine again. PS: I Enabled the Driver again...
-
Bbeisser replied to the thread GMKTEC K12 | Ryzen 7 H 255 | Problem with IGPU.ok, this is interesting. if i disable the radeon 780m in device manager the display shows output. if i enable the device, the output returns to garbage.