Latest activity
-
Kkaveesha kaushan reacted to d0glesby's post in the thread [Help] Dell R740 + Broadcom BCM5720 NDC - Ports Active (Lights On) but Not Detected by Proxmox with
Like.
I have PVE 9.1 running on Dell R740 servers that have some BCM5720 network interfaces. I try to run the latest firmware from Dell, and never had to do any special steps to get this working. These servers previously ran PVE 8 as well with no... -
Kkaveesha kaushan reacted to jdancer's post in the thread [Help] Dell R740 + Broadcom BCM5720 NDC - Ports Active (Lights On) but Not Detected by Proxmox with Like.
I use Dell Intel X550 rNDC in production without issues. Both the 2x1GbE-2x10GbE and 4x10GbE versions. The 10GbE uses the ixgbe driver and the 1GbE uses the igb driver. Use 'dmesg -t' to confirm. Obviously flash the rNDC to the latest firmware...
-
Hhuitheme replied to the thread ProxMox 9.1.2 on MS-01 cannot make i226-V come up.How do I update the firmware for the i226 network card?
-
Jhello everyone below the picture. how to enable encrypted for the pbs bakcup in the web-ui ? my pbs's version is 4.0. was integrated into PVE.
-
-
CC-F-H posted the thread migrate the Guest (Windows & Linux) from ESXi VMDK to PVE host in Proxmox VE: Installation and configuration.We try to migrate the Guest (Windows & Linux) from ESXi VMDK to PVE host,it can run on PVE and ping localhost in no issue but fail to connect to PVE host and outside network? We try to del the nic from guest an reboot it re-scan the network by...
-
EllerholdAG reacted to SteveITS's post in the thread if reboot is triggered pve node goes away too fast before ha migration is finished with Like.
Another way to migrate all VMs (and have them migrate back to the same server) is to enable maintenance mode. On any server run: ha-manager crm-command node-maintenance enable pve1 (wait for migration, then reboot) ha-manager crm-command... -
CC-F-H posted the thread The PVE cluster can connect to NFS via Cluster dashboard from front-end side but fail connect to NFS via Cluster dashboard from back-end side? in Proxmox VE: Installation and configuration.We got the wired situation for now but it kind be urgent. Latest PVE version for now just updated in last night. The actual VM guests should run on NFS Storage so it kind be fuss. NFS Storage have 2 Nics ,one is the front side another is...
-
Sshodan posted the thread Is there an easier way to enable remote ssh root login in the installer ? in Proxmox VE: Installation and configuration.Hi, When I run the proxmox installer, I prefer to do that remotely So, I type the following, fully by hand in the console apt update ; apt install openssh-server -y ; echo "permitrootlogin yes" >> /etc/ssh/sshd_config ; printf "%s\n"...
-
Uuzumo replied to the thread Windows VM stuck on boot with CPU type set to host.Have you made any settings for CPU-related options? The options available for the CPU type host are limited. Unnecessary options can cause the virtual machine to become unstable.
-
Ddingybeaver replied to the thread Can’t login to the web UI.I just saw this, Sorry! I changed my password and that fixed it. Thank you!
-
PPouch6867 replied to the thread Proxmox Virtual Environment 9.1 available!.Moved my cluster to 9.1 from 8.4. Did the management node first for testing and then the hosts. Had a hiccup on OSD authentication in one of the hosts for some reason but got that cleared up relatively quickly. Only side effect from that was...
-
Eegan wu posted the thread Bulk Migrate Parallel jobs become invalid in Proxmox VE: Installation and configuration.repo: no-subscripction i have 2 PVE-clusters, after update one cluster, bulk migrate failed web-ui setting exist but # cat /etc/pve/datacenter.cfg keyboard: en-us migration: insecure,network=10.200.251.13/24 after change by web-ui again...
-
-
weehooey-bh reacted to shanreich's post in the thread Bonded ethernet uplinks broken in pve-common 9.1.1 with Like.
submitted an initial patch, thanks for the report: https://lore.proxmox.com/pve-devel/20251216094329.36089-1-s.hanreich@proxmox.com/T/#u -
Ffseesink replied to the thread Can't upload ISOs via PVE (proxmox 9 ZFS IO Stall).I am currently running Proxmox 9.1.2 and experiencing the same result. I have attempted uploading an ISO twice now with the same result. It says it uploads 100%, but then it shows the following where the only choices are to click the (X) in...
-
-
Rrallymaster replied to the thread What is the reason for USB Network Interface going offline?.Did you decide on another 2.5G dongle that is stable? I have tried the UGREEN and Trendnet both of which stop after 1-2 minutes. Tried a5G Sabrent and it continues to work, but the speed drops over time to 100MB speed. I didn't check to see if...
-
AAndrii.B replied to the thread IO Pressure Stall.I don't feel it, of course. But it's strange, because it's there is less writes on ZFS and iostat show the following: LVM: AVG 1000 r/s, 25 MB/s, 2 %rrqm, 0.4 r_await, 500 w/s, 7 MB/s, 2 %wrqm, 0.05 w_await, 10 %util ZFS: AVG 100 r/s, 1.2 MB/s...
-
Nnightchrono replied to the thread PVE nodes communicating with mounted storage (truenas) over cluster network NIC and not primary NIC.Trying to restore my VM's from PBS and the hypervisor node keeps rebooting on its own
-
Llisthor posted the thread [SOLVED] Network failure after recent update in Proxmox VE: Networking and Firewall.I've just updated Proxmox host, incl. kernel 6.17.4 and after reboot, host lost network access. Strange is that VMs using the same OVS bridge, still have network access. Rebooted host once again to boot using previous kernel and it didn't help...
-
SSkye0 replied to the thread Auto Migration doesn't work when using "reboot" button in webgui.+1 also having an issue today with auto-migration after the update Nodes had a reboot scheduled (probably an autoupgrades patch), they tried to migrate for about 30 minutes, repeatedly fails with: task started by HA resource agent 2025-12-16...
-
Nnightchrono replied to the thread PVE nodes communicating with mounted storage (truenas) over cluster network NIC and not primary NIC.Well this was not the way to do it and am working on recovering my cluster and VMs
