Hallo,
ich habe in meinem Proxmox Server 2 SFP Module eingebaut.
Diese werden auch als enp2s0f0np0 und enp2s0f1np1 erkannt.
Beim Verbinden der Ports mit der Swich leichtet auch die LINK LED an der Switch aber laut Proxmox bleibt der Link down.
Vielen Dank für Eure Hilfe.
Sven
ich habe in meinem Proxmox Server 2 SFP Module eingebaut.
Diese werden auch als enp2s0f0np0 und enp2s0f1np1 erkannt.
Beim Verbinden der Ports mit der Swich leichtet auch die LINK LED an der Switch aber laut Proxmox bleibt der Link down.
Code:
lspci
02:00.1 Ethernet controller: Intel Corporation Ethernet Controller X710 for 10GbE SFP+ (rev 02)
Subsystem: Intel Corporation Ethernet Converged Network Adapter X710
Flags: bus master, fast devsel, latency 0, IRQ 16, IOMMU group 15
Memory at 611c800000 (64-bit, prefetchable) [size=8M]
Memory at 611e000000 (64-bit, prefetchable) [size=32K]
Expansion ROM at 6c800000 [disabled] [size=512K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
Capabilities: [70] MSI-X: Enable+ Count=129 Masked-
Capabilities: [a0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number e2-e5-77-ff-ff-ca-47-58
Capabilities: [150] Alternative Routing-ID Interpretation (ARI)
Capabilities: [160] Single Root I/O Virtualization (SR-IOV)
Capabilities: [1a0] Transaction Processing Hints
Capabilities: [1b0] Access Control Services
Kernel driver in use: i40e
Kernel modules: i40e
ethtool -m enp2s0f1np1
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
Connector : 0x22 (RJ45)
Transceiver codes : 0x10 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x1c
Transceiver type : 10G Ethernet: 10G Base-SR
Transceiver type : Extended: 10Gbase-T Short Reach
Encoding : 0x06 (64B/66B)
BR, Nominal : 10300MBd
Rate identifier : 0x00 (unspecified)
Length (SMF,km) : 0km
Length (SMF) : 0m
Length (50um) : 0m
Length (62.5um) : 0m
Length (Copper) : 30m
Length (OM3) : 0m
Laser wavelength : 0nm
Vendor name : FS
Vendor OUI : 64:9d:99
Vendor PN : SFP-10G-T
Vendor rev : A
Option values : 0x00 0x1a
Option : RX_LOS implemented
Option : TX_FAULT implemented
Option : TX_DISABLE implemented
BR margin, max : 0%
BR margin, min : 0%
Vendor SN : G2340694626
Date code : 240109
ip addr | egrep 'enp|ens'
2: enp87s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master vmbr0 state UP group default qlen 1000
3: enp88s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master vmbr1 state UP group default qlen 1000
4: enp2s0f0np0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq master vmbr2 state DOWN group default qlen 1000
5: enp2s0f1np1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq master vmbr3 state DOWN group default qlen 1000
Vielen Dank für Eure Hilfe.
Sven