Hi there,
Got a new HP DL380 GEN10 Plus with 4 3.84TB SSD on a raid 10 config with a MegaRAID Controller MR416i-a GEN10+
Tried to restore a VM from my Proxmox Backup Server and it stuck at 100% :
waited over an hour but still here !
From other PVE nodes restore VMs from same PBS is working as usual. No issues at all
Any idea ? All nodes (PVEs and PBS are on a 10Gb network)
No errors during boot (no dmesg weird message about megaraid controller):
[ 1.556571] megaraid_sas 0000:86:00.0: BAR:0x0 BAR's base_addr(phys):0x00000000d5000000 mapped virt_addr:0x00000000e64da170
[ 1.556577] megaraid_sas 0000:86:00.0: FW now in Ready state
[ 1.556579] megaraid_sas 0000:86:00.0: 63 bit DMA mask and 63 bit consistent mask
[ 1.556872] megaraid_sas 0000:86:00.0: firmware supports msix : (128)
[ 1.557268] megaraid_sas 0000:86:00.0: requested/available msix 32/32 poll_queue 0
[ 1.557276] megaraid_sas 0000:86:00.0: current msix/max num queues : (32/24)
[ 1.557278] megaraid_sas 0000:86:00.0: RDPQ mode : (enabled)
[ 1.557280] megaraid_sas 0000:86:00.0: Current firmware supports maximum commands: 5101 LDIO threshold: 0
[ 1.568765] megaraid_sas 0000:86:00.0: Performance mode :Balanced (latency index = 8)
[ 1.568768] megaraid_sas 0000:86:00.0: FW supports sync cache : Yes
[ 1.568771] megaraid_sas 0000:86:00.0: megasas_disable_intr_fusion is called outbound_intr_mask:0x40000009
[ 1.653488] megaraid_sas 0000:86:00.0: FW supports atomic descriptor : Yes
[ 1.716486] megaraid_sas 0000:86:00.0: FW provided supportMaxExtLDs: 1 max_lds: 240
[ 1.716498] megaraid_sas 0000:86:00.0: controller type : MR(4096MB)
[ 1.716503] megaraid_sas 0000:86:00.0: Online Controller Reset(OCR) : Enabled
[ 1.716507] megaraid_sas 0000:86:00.0: Secure JBOD support : Yes
[ 1.716511] megaraid_sas 0000:86:00.0: NVMe passthru support : Yes
[ 1.716515] megaraid_sas 0000:86:00.0: FW provided TM TaskAbort/Reset timeout : 6 secs/60 secs
[ 1.716520] megaraid_sas 0000:86:00.0: JBOD sequence map support : Yes
[ 1.716523] megaraid_sas 0000:86:00.0: PCI Lane Margining support : Yes
[ 1.737848] megaraid_sas 0000:86:00.0: NVME page size : (4096)
[ 1.738207] megaraid_sas 0000:86:00.0: megasas_enable_intr_fusion is called outbound_intr_mask:0x40000000
[ 1.738209] megaraid_sas 0000:86:00.0: INIT adapter done
[ 1.740653] megaraid_sas 0000:86:00.0: Snap dump wait time : 15
[ 1.740658] megaraid_sas 0000:86:00.0: pci id : (0x1000)/(0x10e2)/(0x1590)/(0x032a)
[ 1.740659] megaraid_sas 0000:86:00.0: unevenspan support : no
[ 1.740660] megaraid_sas 0000:86:00.0: firmware crash dump : no
[ 1.740661] megaraid_sas 0000:86:00.0: JBOD sequence map : enabled
[ 1.740748] megaraid_sas 0000:86:00.0: Max firmware commands: 5100 shared with default hw_queues = 24 poll_queues 0
but quite sure it's something related to this kind of raid controller in some way
- PVE 9.1.4 running kernel: 6.17.4-2-pve
- PBS 4.1.1 running kernel: 6.17.4-2-pve
- enterprise repo enabled on both hosts
- DL380GEN10+ : updated with latest SPP from December 2025
UPDATE: SOLVED, CRAP LSI CONTROLLER...IT'S NOT WORKING WELL WITH TWO ARRAYS IN PLACE :
- 4 SSD SAS RAID 10 (12GB/S)
- 2 SSD SATA RAID 1 (6GB/S)
REMOVED SECOND ARRAY AND NOW IT WORKS FINE
I WILL REMOVE IT AND INSTALL A P408i
Got a new HP DL380 GEN10 Plus with 4 3.84TB SSD on a raid 10 config with a MegaRAID Controller MR416i-a GEN10+
Tried to restore a VM from my Proxmox Backup Server and it stuck at 100% :
waited over an hour but still here !
From other PVE nodes restore VMs from same PBS is working as usual. No issues at all
Any idea ? All nodes (PVEs and PBS are on a 10Gb network)
No errors during boot (no dmesg weird message about megaraid controller):
[ 1.556571] megaraid_sas 0000:86:00.0: BAR:0x0 BAR's base_addr(phys):0x00000000d5000000 mapped virt_addr:0x00000000e64da170
[ 1.556577] megaraid_sas 0000:86:00.0: FW now in Ready state
[ 1.556579] megaraid_sas 0000:86:00.0: 63 bit DMA mask and 63 bit consistent mask
[ 1.556872] megaraid_sas 0000:86:00.0: firmware supports msix : (128)
[ 1.557268] megaraid_sas 0000:86:00.0: requested/available msix 32/32 poll_queue 0
[ 1.557276] megaraid_sas 0000:86:00.0: current msix/max num queues : (32/24)
[ 1.557278] megaraid_sas 0000:86:00.0: RDPQ mode : (enabled)
[ 1.557280] megaraid_sas 0000:86:00.0: Current firmware supports maximum commands: 5101 LDIO threshold: 0
[ 1.568765] megaraid_sas 0000:86:00.0: Performance mode :Balanced (latency index = 8)
[ 1.568768] megaraid_sas 0000:86:00.0: FW supports sync cache : Yes
[ 1.568771] megaraid_sas 0000:86:00.0: megasas_disable_intr_fusion is called outbound_intr_mask:0x40000009
[ 1.653488] megaraid_sas 0000:86:00.0: FW supports atomic descriptor : Yes
[ 1.716486] megaraid_sas 0000:86:00.0: FW provided supportMaxExtLDs: 1 max_lds: 240
[ 1.716498] megaraid_sas 0000:86:00.0: controller type : MR(4096MB)
[ 1.716503] megaraid_sas 0000:86:00.0: Online Controller Reset(OCR) : Enabled
[ 1.716507] megaraid_sas 0000:86:00.0: Secure JBOD support : Yes
[ 1.716511] megaraid_sas 0000:86:00.0: NVMe passthru support : Yes
[ 1.716515] megaraid_sas 0000:86:00.0: FW provided TM TaskAbort/Reset timeout : 6 secs/60 secs
[ 1.716520] megaraid_sas 0000:86:00.0: JBOD sequence map support : Yes
[ 1.716523] megaraid_sas 0000:86:00.0: PCI Lane Margining support : Yes
[ 1.737848] megaraid_sas 0000:86:00.0: NVME page size : (4096)
[ 1.738207] megaraid_sas 0000:86:00.0: megasas_enable_intr_fusion is called outbound_intr_mask:0x40000000
[ 1.738209] megaraid_sas 0000:86:00.0: INIT adapter done
[ 1.740653] megaraid_sas 0000:86:00.0: Snap dump wait time : 15
[ 1.740658] megaraid_sas 0000:86:00.0: pci id : (0x1000)/(0x10e2)/(0x1590)/(0x032a)
[ 1.740659] megaraid_sas 0000:86:00.0: unevenspan support : no
[ 1.740660] megaraid_sas 0000:86:00.0: firmware crash dump : no
[ 1.740661] megaraid_sas 0000:86:00.0: JBOD sequence map : enabled
[ 1.740748] megaraid_sas 0000:86:00.0: Max firmware commands: 5100 shared with default hw_queues = 24 poll_queues 0
but quite sure it's something related to this kind of raid controller in some way
- PVE 9.1.4 running kernel: 6.17.4-2-pve
- PBS 4.1.1 running kernel: 6.17.4-2-pve
- enterprise repo enabled on both hosts
- DL380GEN10+ : updated with latest SPP from December 2025
UPDATE: SOLVED, CRAP LSI CONTROLLER...IT'S NOT WORKING WELL WITH TWO ARRAYS IN PLACE :
- 4 SSD SAS RAID 10 (12GB/S)
- 2 SSD SATA RAID 1 (6GB/S)
REMOVED SECOND ARRAY AND NOW IT WORKS FINE
I WILL REMOVE IT AND INSTALL A P408i
Last edited: