Proxmox on miniPC with only WiFi onboard

GoldKnight

New Member
Apr 9, 2024
1
0
1
Hello! I'm trying to install proxmox to my GMK Nucbox with no eth onboard.
I've successfuly installed proxmox with only wifi a long time ago (in 2022 year), but I forgot how i've done it. I've brought up WiFi without any additional packages.
Now I have no connection to my AP... But all settings seems to be correct. Can somebody help me?

Here's my config /etc/network/interfaces:
Code:
auto lo
iface lo inet loopback

auto wlo2
iface wlo2 inet static
    address 192.168.1.109
    netmask 255.255.255.0
    gateway 192.168.1.1
    wpa-ssid MYSSID
    wpa-psk 12345678
 
auto vmbr0
iface vmbr0 inet static
    address 192.168.200.1/24
    bridge-ports none
    bridge-stp off
    bridge-fd 0
 
    post-up echo 1>/proc/sys/net/ipv4/ip_forward
    post-up iptables -t nat -A POSTROUTING-S '192.168.200.0/24'-o wlo2 -j MASQUERADE
    post-down iptables -t nat -D POSTROUTING-S '192.168.200.0/24'-o wlo2 -j MASQUERADE
 
    post-up iptables -t raw -I PREROUTING -i fwbr+ -j CT --zone 1
    post-down iptables -t raw -D PREROUTING -i fwbn+ -j CT --zone 1

source /etc/network/interfaces.d/*

ip a:
Code:
1: lo: <LOOPBACK, UP, LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
        validlft forever preferred_lft forever
    inet6::1/128 scope host noprefixroute
        validlft forever preferred_lft forever
2: wlo2: <NO-CARRIER, BROADCAST, MULTICAST, UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000
    link/ether 44:af:28:50:37:cd brd ff:ff:ff:ff:ff:ff
    altname wlpθs12f0
    inet 192.168.1.109/24 scope global wlo2
        validlft forever preferred_lft forever
3: vmbr0: <BROADCAST, MULTICAST, UP, LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
    link/ether 2a:ef :53:4c:9f:Bc brd ff:ff:ff:ff:ff:ff
    inet 192.168.200.1/24 Scope global vmbr0
        valid_lft forever preferredlft forever
    inet6 fe80::28ef:53ff:fe4c:9fBC/64 Ssope link
        valid_lft forever preferred_lft forever

dmesg | grep -e iwl -e wlp
Code:
[6.012956] iwlwifi 0000:00:0C.0: enabling device (0000->0002)
[6.063434] iwlwifi 0000:00:OC.O: Detected crf-id Ox2816, cny-id ox1000100 wfpm id OxB0000000
[6.063453] iwlwifi 0000:00:OC.0: PCI dev 31dc/0264, rev=0X312, rfid=0X108110
[6.129277] iwlwifi 0000:00:OC.O: HRT: Overriding region id O
[6.129289] iwlwifi 0000:00:OC.0:HRT: Overriding region id 1
[6.129292] iwlwifi 0000:00:OC.0: HRT:Overriding region id 2
[6.129295] iwlwifi 0000:00:OC.0: HRT: Overriding region id 3
[6.129297] iwlwifi 0000:00:OC.O: HRT: Overriding region id 4
[6.129299] iwlwifi 0000:00:OC.O: HRT: Overriding region id 6
[6.129301] iwlwifi 0000:00:OC.0: HRT: Overniding region id 8
[6.129303] iwlwifi 0000:00:OC.0: HRT: Overriding region id 9
[6.129304] iwlwifi 0000:00:OC.O: HRT: Overriding region id 10
[6.129306] iwlwifi O000:00:0C.0: HRT: Overriding region id 11
[6.129308] iwlwifi 0000:00:Oc.0: HRT: Overriding region id 15
[6.129310l iwlwifi 0000:00:0C.0: HRT: Overriding region id 16
[6.129312] iwlwifi 0000:00:0c.0: HRT: Overriding region id 18
[6.129314] iwlwifi 0000:00:0C.0: HRT: Overriding region id 19
[6.129315] iwlwifi 0000:00:0C.0: HRT: Overriding region id 20
[6.129317] iwlwifi 0000:00:0C.0: HRT: Overriding region id 21
[6.129320] iwlwifi 0000:00:θc.0: HRT: Overriding region id 28
[6.130046] iwlwifi 0800:00:0C.0: loaded firmware version 46.ff18e32a.0 9000-pu-be-jf-bo-46.ucode op_mode iwlmym
[7.212339] iwlwifi 0000:00:0C.0: Detected Intel(R)Wireless-AC 9461, REV03312
[7.342083] iwlwifi 0000:00:0C.0: base H address: 44:af:28:50:37:cd, OTP minor version: Ox4
[7.384878] ieee80211 phyo: Selected rate control algorithm iwl-mvm-rs
[7.408699] iwlwifi 0000:00:θC.O wl02: renamed from wlane
[9.844660] iwlwifi 0000:00:OC.0:Conf1ict between TLV & NVM regarding enabling LAR (TLV= enabled NVM =disabled)
[9.845117] iwlwif1 0000:00:OC.0: Registered PHC clock: iwlwifi-PTP, with index:0

There can be some mistakes in code because text was made from the pictures of screen - sorry for this.
 
Last edited:

About

The Proxmox community has been around for many years and offers help and support for Proxmox VE, Proxmox Backup Server, and Proxmox Mail Gateway.
We think our community is one of the best thanks to people like you!

Get your subscription!

The Proxmox team works very hard to make sure you are running the best software and getting stable updates and security enhancements, as well as quick enterprise support. Tens of thousands of happy customers have a Proxmox subscription. Get yours easily in our online shop.

Buy now!