Hi,
I installed a one-node cluster on the network segment 10.0.0.0/22. Everything was O.K. but when I put it on the segment 10.31.0.0/24 the node began not to work.
The problem is that I cant' configure crushmap because of timeout of different tools. There is a "?" mark on the storage. ceph -s, ceoh health, getcrushmap all have timeout.
Every target daemon seem to be working except ceph-mon
Here is the syslog:
Dec 17 18:36:50 pve8tb ceph-mon[46173]: 2021-12-17T18:36:50.917+0100 7efe39fdb580 -1 WARNING: 'mon addr' config option v1:10.31.0.70:6789/0 does not match monmap file
Dec 17 18:36:50 pve8tb ceph-mon[46173]: continuing with monmap configuration
Dec 17 18:36:50 pve8tb ceph-mon[46173]: 2021-12-17T18:36:50.925+0100 7efe39fdb580 -1 Processor -- bind unable to bind to v2:10.0.0.70:3300/0: (99) Cannot assign requested address
Dec 17 18:36:50 pve8tb ceph-mon[46173]: 2021-12-17T18:36:50.925+0100 7efe39fdb580 -1 Processor -- bind was unable to bind. Trying again in 5 seconds
Dec 17 18:36:55 pve8tb ceph-mon[46173]: 2021-12-17T18:36:55.929+0100 7efe39fdb580 -1 Processor -- bind unable to bind to v2:10.0.0.70:3300/0: (99) Cannot assign requested address
Dec 17 18:36:55 pve8tb ceph-mon[46173]: 2021-12-17T18:36:55.929+0100 7efe39fdb580 -1 Processor -- bind was unable to bind. Trying again in 5 seconds
Dec 17 18:37:00 pve8tb ceph-mon[46173]: 2021-12-17T18:37:00.925+0100 7efe39fdb580 -1 Processor -- bind unable to bind to v2:10.0.0.70:3300/0: (99) Cannot assign requested address
Dec 17 18:37:00 pve8tb ceph-mon[46173]: 2021-12-17T18:37:00.925+0100 7efe39fdb580 -1 Processor -- bind was unable to bind after 3 attempts: (99) Cannot assign requested address
Dec 17 18:37:00 pve8tb ceph-mon[46173]: 2021-12-17T18:37:00.925+0100 7efe39fdb580 -1 unable to bind monitor to [v2:10.0.0.70:3300/0,v1:10.0.0.70:6789/0]
Dec 17 18:37:00 pve8tb systemd[1]: ceph-mon@pve8tb.service: Main process exited, code=exited, status=1/FAILURE
If I put the node back on the old segment and replaced the address in crushmap to the new ip address with crushmap tools would it work?
What should I do anyway?
ZKallo
I installed a one-node cluster on the network segment 10.0.0.0/22. Everything was O.K. but when I put it on the segment 10.31.0.0/24 the node began not to work.
The problem is that I cant' configure crushmap because of timeout of different tools. There is a "?" mark on the storage. ceph -s, ceoh health, getcrushmap all have timeout.
Every target daemon seem to be working except ceph-mon
Here is the syslog:
Dec 17 18:36:50 pve8tb ceph-mon[46173]: 2021-12-17T18:36:50.917+0100 7efe39fdb580 -1 WARNING: 'mon addr' config option v1:10.31.0.70:6789/0 does not match monmap file
Dec 17 18:36:50 pve8tb ceph-mon[46173]: continuing with monmap configuration
Dec 17 18:36:50 pve8tb ceph-mon[46173]: 2021-12-17T18:36:50.925+0100 7efe39fdb580 -1 Processor -- bind unable to bind to v2:10.0.0.70:3300/0: (99) Cannot assign requested address
Dec 17 18:36:50 pve8tb ceph-mon[46173]: 2021-12-17T18:36:50.925+0100 7efe39fdb580 -1 Processor -- bind was unable to bind. Trying again in 5 seconds
Dec 17 18:36:55 pve8tb ceph-mon[46173]: 2021-12-17T18:36:55.929+0100 7efe39fdb580 -1 Processor -- bind unable to bind to v2:10.0.0.70:3300/0: (99) Cannot assign requested address
Dec 17 18:36:55 pve8tb ceph-mon[46173]: 2021-12-17T18:36:55.929+0100 7efe39fdb580 -1 Processor -- bind was unable to bind. Trying again in 5 seconds
Dec 17 18:37:00 pve8tb ceph-mon[46173]: 2021-12-17T18:37:00.925+0100 7efe39fdb580 -1 Processor -- bind unable to bind to v2:10.0.0.70:3300/0: (99) Cannot assign requested address
Dec 17 18:37:00 pve8tb ceph-mon[46173]: 2021-12-17T18:37:00.925+0100 7efe39fdb580 -1 Processor -- bind was unable to bind after 3 attempts: (99) Cannot assign requested address
Dec 17 18:37:00 pve8tb ceph-mon[46173]: 2021-12-17T18:37:00.925+0100 7efe39fdb580 -1 unable to bind monitor to [v2:10.0.0.70:3300/0,v1:10.0.0.70:6789/0]
Dec 17 18:37:00 pve8tb systemd[1]: ceph-mon@pve8tb.service: Main process exited, code=exited, status=1/FAILURE
If I put the node back on the old segment and replaced the address in crushmap to the new ip address with crushmap tools would it work?
What should I do anyway?
ZKallo