ixgbe problems with an Intel x520-DA2 card.

G

GT1

Active Member
Aug 10, 2011
48
0
26
Hello.

I have an Intel x520-DA2 10Gig card, SFPs from Intel, that does not "start up" after booting the current PVE version. As in, during boot the link leds on the card go off and stay that way.

However, when i physically unplug & replug the SFP, the link becomes available (ixgbe 0000:81:00.1 eth3: NIC Link is Up 10 Gbps, Flow Control: RX/TX).

I do not have that problem with a barebone Debian Jessie install, the interfaces come up just fine (Kernel 3.16.0-4-amd64, ixgbe 3.19.1-k).

Tried the "allow_unsupported_sfp" and "ip link set ethX up" or "ethtool -r eth2" without success. So far, only pulling the SFP out & back in works so far.

Code: 
proxmox-ve: 4.2-58 (running kernel: 4.4.13-2-pve)
pve-manager: 4.2-17 (running version: 4.2-17/e1400248)
pve-kernel-4.4.6-1-pve: 4.4.6-48
pve-kernel-4.4.13-1-pve: 4.4.13-56
pve-kernel-4.4.13-2-pve: 4.4.13-58
lvm2: 2.02.116-pve2
corosync-pve: 2.3.5-2
libqb0: 1.0-1
pve-cluster: 4.0-43
qemu-server: 4.0-85
pve-firmware: 1.1-8
libpve-common-perl: 4.0-71
libpve-access-control: 4.0-17
libpve-storage-perl: 4.0-56
pve-libspice-server1: 0.12.8-1
vncterm: 1.2-1
pve-qemu-kvm: 2.6-1
pve-container: 1.0-71
pve-firewall: 2.0-29
pve-ha-manager: 1.0-32
ksm-control-daemon: 1.2-1
glusterfs-client: 3.5.2-2+deb8u2
lxc-pve: 1.1.5-7
lxcfs: 2.0.0-pve2
cgmanager: 0.39-pve1
criu: 1.6.0-1
zfsutils: 0.6.5.7-pve10~bpo80

Code: 
filename:  /lib/modules/4.4.13-2-pve/kernel/drivers/net/ethernet/intel/ixgbe/ixgbe.ko
version:  4.4.6
license:  GPL
description:  Intel(R) 10GbE PCI Express Linux Network Driver
author:  Intel Corporation, <linux.nics@intel.com>
srcversion:  A0F436FF26ECE3DC8455D1E
alias:  pci:v00008086d000015ADsv*sd*bc*sc*i*
alias:  pci:v00008086d000015ACsv*sd*bc*sc*i*
alias:  pci:v00008086d000015ABsv*sd*bc*sc*i*
alias:  pci:v00008086d000015AAsv*sd*bc*sc*i*
alias:  pci:v00008086d000015D1sv*sd*bc*sc*i*
alias:  pci:v00008086d00001563sv*sd*bc*sc*i*
alias:  pci:v00008086d00001560sv*sd*bc*sc*i*
alias:  pci:v00008086d00001558sv*sd*bc*sc*i*
alias:  pci:v00008086d0000154Asv*sd*bc*sc*i*
alias:  pci:v00008086d00001557sv*sd*bc*sc*i*
alias:  pci:v00008086d0000154Fsv*sd*bc*sc*i*
alias:  pci:v00008086d0000154Dsv*sd*bc*sc*i*
alias:  pci:v00008086d00001528sv*sd*bc*sc*i*
alias:  pci:v00008086d000010F8sv*sd*bc*sc*i*
alias:  pci:v00008086d0000151Csv*sd*bc*sc*i*
alias:  pci:v00008086d00001529sv*sd*bc*sc*i*
alias:  pci:v00008086d0000152Asv*sd*bc*sc*i*
alias:  pci:v00008086d000010F9sv*sd*bc*sc*i*
alias:  pci:v00008086d00001514sv*sd*bc*sc*i*
alias:  pci:v00008086d00001507sv*sd*bc*sc*i*
alias:  pci:v00008086d000010FBsv*sd*bc*sc*i*
alias:  pci:v00008086d00001517sv*sd*bc*sc*i*
alias:  pci:v00008086d000010FCsv*sd*bc*sc*i*
alias:  pci:v00008086d000010F7sv*sd*bc*sc*i*
alias:  pci:v00008086d00001508sv*sd*bc*sc*i*
alias:  pci:v00008086d000010DBsv*sd*bc*sc*i*
alias:  pci:v00008086d000010F4sv*sd*bc*sc*i*
alias:  pci:v00008086d000010E1sv*sd*bc*sc*i*
alias:  pci:v00008086d000010F1sv*sd*bc*sc*i*
alias:  pci:v00008086d000010ECsv*sd*bc*sc*i*
alias:  pci:v00008086d000010DDsv*sd*bc*sc*i*
alias:  pci:v00008086d0000150Bsv*sd*bc*sc*i*
alias:  pci:v00008086d000010C8sv*sd*bc*sc*i*
alias:  pci:v00008086d000010C7sv*sd*bc*sc*i*
alias:  pci:v00008086d000010C6sv*sd*bc*sc*i*
alias:  pci:v00008086d000010B6sv*sd*bc*sc*i*
depends:  ptp,dca,vxlan
vermagic:  4.4.13-2-pve SMP mod_unload modversions
parm:  InterruptType:Change Interrupt Mode (0=Legacy, 1=MSI, 2=MSI-X), default IntMode (deprecated) (array of int)
parm:  IntMode:Change Interrupt Mode (0=Legacy, 1=MSI, 2=MSI-X), default 2 (array of int)
parm:  MQ:Disable or enable Multiple Queues, default 1 (array of int)
parm:  DCA:Disable or enable Direct Cache Access, 0=disabled, 1=descriptor only, 2=descriptor and data (array of int)
parm:  RSS:Number of Receive-Side Scaling Descriptor Queues, default 0=number of cpus (array of int)
parm:  VMDQ:Number of Virtual Machine Device Queues: 0/1 = disable (1 queue) 2-16 enable (default=8) (array of int)
parm:  max_vfs:Number of Virtual Functions: 0 = disable (default), 1-63 = enable this many VFs (array of int)
parm:  VEPA:VEPA Bridge Mode: 0 = VEB (default), 1 = VEPA (array of int)
parm:  InterruptThrottleRate:Maximum interrupts per second, per vector, (0,1,956-488281), default 1 (array of int)
parm:  LLIPort:Low Latency Interrupt TCP Port (0-65535) (array of int)
parm:  LLIPush:Low Latency Interrupt on TCP Push flag (0,1) (array of int)
parm:  LLISize:Low Latency Interrupt on Packet Size (0-1500) (array of int)
parm:  LLIEType:Low Latency Interrupt Ethernet Protocol Type (array of int)
parm:  LLIVLANP:Low Latency Interrupt on VLAN priority threshold (array of int)
parm:  FdirPballoc:Flow Director packet buffer allocation level:
  1 = 8k hash filters or 2k perfect filters
  2 = 16k hash filters or 4k perfect filters
  3 = 32k hash filters or 8k perfect filters (array of int)
parm:  AtrSampleRate:Software ATR Tx packet sample rate (array of int)
parm:  FCoE:Disable or enable FCoE Offload, default 1 (array of int)
parm:  MDD:Malicious Driver Detection: (0,1), default 1 = on (array of int)
parm:  LRO:Large Receive Offload (0,1), default 0 = off (array of int)
parm:  allow_unsupported_sfp:Allow unsupported and untested SFP+ modules on 82599 based adapters, default 0 = Disable (array of int)
parm:  dmac_watchdog:DMA coalescing watchdog in microseconds (0,41-10000), default 0 = off (array of int)
parm:  vxlan_rx:VXLAN receive checksum offload (0,1), default 1 = Enable (array of int)

Code: 
[  2.517622] ixgbe: 0000:04:00.0: ixgbe_check_options: FCoE Offload feature enabled
[  3.150936] ixgbe 0000:04:00.0: PCI Express bandwidth of 32GT/s available
[  3.150939] ixgbe 0000:04:00.0: (Speed:5.0GT/s, Width: x8, Encoding Loss:20%)
[  3.191182] ixgbe 0000:04:00.0 eth0: MAC: 3, PHY: 3, PBA No: 030C00-000
[  3.191188] ixgbe 0000:04:00.0: 0c:c4:7a:6f:37:a0
[  3.191192] ixgbe 0000:04:00.0 eth0: Enabled Features: RxQ: 40 TxQ: 40 FdirHash
[  3.213378] ixgbe 0000:04:00.0 eth0: Intel(R) 10 Gigabit Network Connection
[  3.213623] ixgbe: 0000:04:00.1: ixgbe_check_options: FCoE Offload feature enabled
[  3.851388] ixgbe 0000:04:00.1: PCI Express bandwidth of 32GT/s available
[  3.851391] ixgbe 0000:04:00.1: (Speed:5.0GT/s, Width: x8, Encoding Loss:20%)
[  3.891640] ixgbe 0000:04:00.1 eth1: MAC: 3, PHY: 3, PBA No: 030C00-000
[  3.891648] ixgbe 0000:04:00.1: 0c:c4:7a:6f:37:a1
[  3.891652] ixgbe 0000:04:00.1 eth1: Enabled Features: RxQ: 40 TxQ: 40 FdirHash
[  3.913851] ixgbe 0000:04:00.1 eth1: Intel(R) 10 Gigabit Network Connection
[  3.934518] ixgbe: 0000:81:00.0: ixgbe_check_options: FCoE Offload feature enabled
[  4.073508] ixgbe 0000:81:00.0: PCI Express bandwidth of 32GT/s available
[  4.073511] ixgbe 0000:81:00.0: (Speed:5.0GT/s, Width: x8, Encoding Loss:20%)
[  4.073594] ixgbe 0000:81:00.0 eth2: MAC: 2, PHY: 18, SFP+: 5, PBA No: E68793-006
[  4.073596] ixgbe 0000:81:00.0: 90:e2:ba:61:15:f4
[  4.073599] ixgbe 0000:81:00.0 eth2: Enabled Features: RxQ: 40 TxQ: 40 FdirHash
[  4.073648] ixgbe 0000:81:00.0 eth2: Intel(R) 10 Gigabit Network Connection
[  4.094227] ixgbe: 0000:81:00.1: ixgbe_check_options: FCoE Offload feature enabled
[  4.241471] ixgbe 0000:81:00.1: PCI Express bandwidth of 32GT/s available
[  4.241475] ixgbe 0000:81:00.1: (Speed:5.0GT/s, Width: x8, Encoding Loss:20%)
[  4.241558] ixgbe 0000:81:00.1 eth3: MAC: 2, PHY: 18, SFP+: 6, PBA No: E68793-006
[  4.241560] ixgbe 0000:81:00.1: 90:e2:ba:61:15:f5
[  4.241562] ixgbe 0000:81:00.1 eth3: Enabled Features: RxQ: 40 TxQ: 40 FdirHash
[  4.241609] ixgbe 0000:81:00.1 eth3: Intel(R) 10 Gigabit Network Connection
[  10.611497] ixgbe 0000:81:00.0: registered PHC device on eth2
[  10.779740] ixgbe 0000:81:00.0 eth2: detected SFP+: 5
[  11.245392] ixgbe 0000:81:00.1: registered PHC device on eth3
[  11.576488] ixgbe 0000:04:00.0: registered PHC device on eth0
[  12.396296] ixgbe 0000:81:00.1 eth3: detected SFP+: 6
[  14.703531] ixgbe 0000:04:00.0 eth0: NIC Link is Up 1 Gbps, Flow Control: RX/TX

So, maybe ixgbe version related ? Anyone got any hints on where to look ?

Thanks.
 
Last edited:
Code: 
81:00.0 Ethernet controller [0200]: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection [8086:10fb] (rev 01)
  Subsystem: Intel Corporation Ethernet Server Adapter X520-2 [8086:0003]
  Physical Slot: 4
  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
  Latency: 0, Cache Line Size: 32 bytes
  Interrupt: pin A routed to IRQ 33
  Region 0: Memory at 387fffd80000 (64-bit, prefetchable) [size=512K]
  Region 2: I/O ports at f020 [size=32]
  Region 4: Memory at 387fffe04000 (64-bit, prefetchable) [size=16K]
  Capabilities: [40] Power Management version 3
  Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
  Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
  Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
  Address: 0000000000000000  Data: 0000
  Masking: 00000000  Pending: 00000000
  Capabilities: [70] MSI-X: Enable+ Count=64 Masked-
  Vector table: BAR=4 offset=00000000
  PBA: BAR=4 offset=00002000
  Capabilities: [a0] Express (v2) Endpoint, MSI 00
  DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
  ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
  DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
  RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
  MaxPayload 256 bytes, MaxReadReq 512 bytes
  DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
  LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s, Exit Latency L0s <1us, L1 <8us
  ClockPM- Surprise- LLActRep- BwNot-
  LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
  ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
  LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
  DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported
  DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
  LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
  Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
  Compliance De-emphasis: -6dB
  LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
  EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
  Capabilities: [100 v1] Advanced Error Reporting
  UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
  UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
  UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
  CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
  CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
  AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
  Capabilities: [140 v1] Device Serial Number 90-e2-ba-ff-ff-61-15-f4
  Capabilities: [150 v1] Alternative Routing-ID Interpretation (ARI)
  ARICap: MFVC- ACS-, Next Function: 1
  ARICtl: MFVC- ACS-, Function Group: 0
  Capabilities: [160 v1] Single Root I/O Virtualization (SR-IOV)
  IOVCap: Migration-, Interrupt Message Number: 000
  IOVCtl: Enable- Migration- Interrupt- MSE- ARIHierarchy+
  IOVSta: Migration-
  Initial VFs: 64, Total VFs: 64, Number of VFs: 0, Function Dependency Link: 00
  VF offset: 128, stride: 2, Device ID: 10ed
  Supported Page Size: 00000553, System Page Size: 00000001
  Region 0: Memory at 00000000fbe00000 (64-bit, non-prefetchable)
  Region 3: Memory at 00000000fbd00000 (64-bit, non-prefetchable)
  VF Migration: offset: 00000000, BIR: 0
  Kernel driver in use: ixgbe

81:00.1 Ethernet controller [0200]: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection [8086:10fb] (rev 01)
  Subsystem: Intel Corporation Ethernet Server Adapter X520-2 [8086:0003]
  Physical Slot: 4
  Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
  Latency: 0, Cache Line Size: 32 bytes
  Interrupt: pin B routed to IRQ 164
  Region 0: Memory at 387fffd00000 (64-bit, prefetchable) [size=512K]
  Region 2: I/O ports at f000 [size=32]
  Region 4: Memory at 387fffe00000 (64-bit, prefetchable) [size=16K]
  Capabilities: [40] Power Management version 3
  Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
  Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
  Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
  Address: 0000000000000000  Data: 0000
  Masking: 00000000  Pending: 00000000
  Capabilities: [70] MSI-X: Enable+ Count=64 Masked-
  Vector table: BAR=4 offset=00000000
  PBA: BAR=4 offset=00002000
  Capabilities: [a0] Express (v2) Endpoint, MSI 00
  DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
  ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
  DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
  RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
  MaxPayload 256 bytes, MaxReadReq 512 bytes
  DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
  LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s, Exit Latency L0s <1us, L1 <8us
  ClockPM- Surprise- LLActRep- BwNot-
  LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
  ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
  LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
  DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported
  DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
  LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
  EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
  Capabilities: [100 v1] Advanced Error Reporting
  UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
  UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
  UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
  CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
  CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
  AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
  Capabilities: [140 v1] Device Serial Number 90-e2-ba-ff-ff-61-15-f4
  Capabilities: [150 v1] Alternative Routing-ID Interpretation (ARI)
  ARICap: MFVC- ACS-, Next Function: 0
  ARICtl: MFVC- ACS-, Function Group: 0
  Capabilities: [160 v1] Single Root I/O Virtualization (SR-IOV)
  IOVCap: Migration-, Interrupt Message Number: 000
  IOVCtl: Enable- Migration- Interrupt- MSE- ARIHierarchy-
  IOVSta: Migration-
  Initial VFs: 64, Total VFs: 64, Number of VFs: 0, Function Dependency Link: 01
  VF offset: 128, stride: 2, Device ID: 10ed
  Supported Page Size: 00000553, System Page Size: 00000001
  Region 0: Memory at 00000000fbc00000 (64-bit, non-prefetchable)
  Region 3: Memory at 00000000fbb00000 (64-bit, non-prefetchable)
  VF Migration: offset: 00000000, BIR: 0
  Kernel driver in use: ixgbe
 
Code: 
  Identifier  : 0x03 (SFP)
  Extended identifier  : 0x04 (GBIC/SFP defined by 2-wire interface ID)
  Connector  : 0x07 (LC)
  Transceiver codes  : 0x10 0x00 0x00 0x01 0x00 0x00 0x00 0x00
  Transceiver type  : 10G Ethernet: 10G Base-SR
  Transceiver type  : Ethernet: 1000BASE-SX
  Encoding  : 0x06 (64B/66B)
  BR, Nominal  : 10300MBd
  Rate identifier  : 0x00 (unspecified)
  Length (SMF,km)  : 0km
  Length (SMF)  : 0m
  Length (50um)  : 80m
  Length (62.5um)  : 30m
  Length (Copper)  : 0m
  Length (OM3)  : 300m
  Laser wavelength  : 850nm
  Vendor name  : Intel
  Vendor OUI  : 00:1b:21
  Vendor PN  : SFP-10G-SR
  Vendor rev  : 1.0
  Optical diagnostics support  : Yes
  Laser bias current  : 18.752 mA
  Laser output power  : 0.0577 mW / -12.39 dBm
  Receiver signal average optical power  : 0.5815 mW / -2.35 dBm
  Module temperature  : 36.62 degrees C / 97.92 degrees F
  Module voltage  : 3.2263 V
  Alarm/warning flags implemented  : Yes
  Laser bias current high alarm  : Off
  Laser bias current low alarm  : On
  Laser bias current high warning  : Off
  Laser bias current low warning  : On
  Laser output power high alarm  : Off
  Laser output power low alarm  : On
  Laser output power high warning  : Off
  Laser output power low warning  : On
  Module temperature high alarm  : Off
  Module temperature low alarm  : Off
  Module temperature high warning  : Off
  Module temperature low warning  : Off
  Module voltage high alarm  : Off
  Module voltage low alarm  : Off
  Module voltage high warning  : Off
  Module voltage low warning  : Off
  Laser rx power high alarm  : Off
  Laser rx power low alarm  : Off
  Laser rx power high warning  : Off
  Laser rx power low warning  : Off
  Laser bias current high alarm threshold  : 12.000 mA
  Laser bias current low alarm threshold  : 1.000 mA
  Laser bias current high warning threshold : 11.000 mA
  Laser bias current low warning threshold  : 2.000 mA
  Laser output power high alarm threshold  : 1.0000 mW / 0.00 dBm
  Laser output power low alarm threshold  : 0.1413 mW / -8.50 dBm
  Laser output power high warning threshold : 0.7943 mW / -1.00 dBm
  Laser output power low warning threshold  : 0.1778 mW / -7.50 dBm
  Module temperature high alarm threshold  : 75.00 degrees C / 167.00 degrees F
  Module temperature low alarm threshold  : -10.00 degrees C / 14.00 degrees F
  Module temperature high warning threshold : 70.00 degrees C / 158.00 degrees F
  Module temperature low warning threshold  : -5.00 degrees C / 23.00 degrees F
  Module voltage high alarm threshold  : 3.6000 V
  Module voltage low alarm threshold  : 3.0000 V
  Module voltage high warning threshold  : 3.5000 V
  Module voltage low warning threshold  : 3.1000 V
  Laser rx power high alarm threshold  : 1.0000 mW / 0.00 dBm
  Laser rx power low alarm threshold  : 0.0398 mW / -14.00 dBm
  Laser rx power high warning threshold  : 0.7943 mW / -1.00 dBm
  Laser rx power low warning threshold  : 0.0631 mW / -12.00 dBm

Code: 
eth0  Link encap:Ethernet  HWaddr 0c:c4:7a:6f:37:a0
  UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
  RX packets:15943 errors:0 dropped:0 overruns:0 frame:0
  TX packets:953 errors:0 dropped:0 overruns:0 carrier:0
  collisions:0 txqueuelen:1000
  RX bytes:2081314 (1.9 MiB)  TX bytes:287513 (280.7 KiB)

eth2  Link encap:Ethernet  HWaddr 90:e2:ba:61:15:f4
  inet addr:192.168.230.85  Bcast:192.168.230.255  Mask:255.255.255.0
  UP BROADCAST MULTICAST  MTU:1500  Metric:1
  RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  collisions:0 txqueuelen:1000
  RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth3  Link encap:Ethernet  HWaddr 90:e2:ba:61:15:f5
  inet addr:192.168.240.85  Bcast:192.168.240.255  Mask:255.255.255.0
  inet6 addr: fe80::92e2:baff:fe61:15f5/64 Scope:Link
  UP BROADCAST MULTICAST  MTU:1500  Metric:1
  RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  collisions:0 txqueuelen:1000
  RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo  Link encap:Local Loopback
  inet addr:127.0.0.1  Mask:255.0.0.0
  inet6 addr: ::1/128 Scope:Host
  UP LOOPBACK RUNNING  MTU:65536  Metric:1
  RX packets:2 errors:0 dropped:0 overruns:0 frame:0
  TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
  collisions:0 txqueuelen:1
  RX bytes:190 (190.0 B)  TX bytes:190 (190.0 B)

vmbr0  Link encap:Ethernet  HWaddr 0c:c4:7a:6f:37:a0
  inet addr:192.168.190.85  Bcast:192.168.190.255  Mask:255.255.255.0
  inet6 addr: fe80::ec4:7aff:fe6f:37a0/64 Scope:Link
  UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
  RX packets:14282 errors:0 dropped:0 overruns:0 frame:0
  TX packets:926 errors:0 dropped:0 overruns:0 carrier:0
  collisions:0 txqueuelen:1000
  RX bytes:1711259 (1.6 MiB)  TX bytes:286055 (279.3 KiB)

Code: 
auto lo
iface lo inet loopback

iface eth0 inet manual

iface eth1 inet manual

auto eth2
iface eth2 inet static
  address  192.168.230.85
  netmask  255.255.255.0

auto eth3
iface eth3 inet static
  address  192.168.240.85
  netmask  255.255.255.0

auto vmbr0
iface vmbr0 inet static
  address  192.168.190.85
  netmask  255.255.255.0
  gateway  192.168.190.1
  bridge_ports eth0
  bridge_stp off
  bridge_fd 0

Code: 
driver: ixgbe
version: 4.4.6
firmware-version: 0x61c10001
bus-info: 0000:81:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: yes
 
Last edited:
Hello, Have you found a solution ? I'm facing exactly the same problem.
 
You must log in or register to reply here.

About

The Proxmox community has been around for many years and offers help and support for Proxmox VE, Proxmox Backup Server, and Proxmox Mail Gateway.
We think our community is one of the best thanks to people like you!

Quick Navigation

Home Get Subscription Wiki Downloads Proxmox Customer Portal About

Get your subscription!

The Proxmox team works very hard to make sure you are running the best software and getting stable updates and security enhancements, as well as quick enterprise support. Tens of thousands of happy customers have a Proxmox subscription. Get yours easily in our online shop.

Buy now!
Community platform by XenForo® © 2010-2024 XenForo Ltd.
Top Bottom
Back