[HELP ME] How to connect VMs From Remote Desktop

[Rudi182]

i am beginner in proxmox.. please help me..

How to connect VMs from IP Public (Remote desktop) ?? please someone write every steps

i have create 2 Vm (vm1=windows,vm2=debian) i have 5ipv4 Ip failover . i want the VM connect from RDP/VNC (windows) with IP failover.

This The Network Interface

# The loopback network interface
auto lo
iface lo inet loopback

# for Routing
auto vmbr1
iface vmbr1 inet manual
post-up /etc/pve/kvm-networking.sh
bridge_ports dummy0
bridge_stp off
bridge_fd 0

# vmbr0: Bridging. Make sure to use only MAC adresses that were assigned to you.
auto vmbr0
iface vmbr0 inet static
address 167.214.108.196
netmask 255.255.255.0
network 167.214.208.0
broadcast 167.214.108.255
gateway 167.214.208.254
bridge_ports eth0
bridge_stp off
bridge_fd 0

iface vmbr0 inet6 static
address 2612:5300:60:77c4::
netmask 64
post-up /sbin/ip -f inet6 route add 2612:5300:60:77ff:ff:ff:ff:ff dev v$
post-up /sbin/ip -f inet6 route add default via 2612:5300:60:77ff:ff:ff$
pre-down /sbin/ip -f inet6 route del default via 2612:5300:60:77ff:ff:f$
pre-down /sbin/ip -f inet6 route del 2612:5300:60:77ff:ff:ff:ff:ff dev $

Please Help....

 

[pirateghost]

you should probably give a little more info than that.

what are you trying to accomplish?

what remote desktop are you talking about? Windows?

how is your ProxMox configured?

What is your networking setup?

 

[Rudi182]

you should probably give a little more info than that.

what are you trying to accomplish?

what remote desktop are you talking about? Windows?

how is your ProxMox configured?

What is your networking setup?

i have create 2 Vm (vm1=windows,vm2=debian) i have 5ipv4 Ip failover . i want the VM connect from RDP/VNC (windows) with IP failover

This The Network Interface

# The loopback network interface
auto lo
iface lo inet loopback

# for Routing
auto vmbr1
iface vmbr1 inet manual
post-up /etc/pve/kvm-networking.sh
bridge_ports dummy0
bridge_stp off
bridge_fd 0

# vmbr0: Bridging. Make sure to use only MAC adresses that were assigned to you.
auto vmbr0
iface vmbr0 inet static
address 167.214.108.196
netmask 255.255.255.0
network 167.214.208.0
broadcast 167.214.108.255
gateway 167.214.208.254
bridge_ports eth0
bridge_stp off
bridge_fd 0

iface vmbr0 inet6 static
address 2612:5300:60:77c4::
netmask 64
post-up /sbin/ip -f inet6 route add 2612:5300:60:77ff:ff:ff:ff:ff dev v$
post-up /sbin/ip -f inet6 route add default via 2612:5300:60:77ff:ff:ff$
pre-down /sbin/ip -f inet6 route del default via 2612:5300:60:77ff:ff:f$
pre-down /sbin/ip -f inet6 route del 2612:5300:60:77ff:ff:ff:ff:ff dev $

Please Help....

 

[kotakomputer]

i have create 2 Vm (vm1=windows,vm2=debian) i have 5ipv4 Ip failover . i want the VM connect from RDP/VNC (windows) with IP failover

Server Manager:

1. For most Provider, you must go to their Server Manager then Add Virtual MAC to your IP
2. Edit your VPS-- replace existing with Virtual MAC from step #1
3. Stop then Start the VM

Inside Windows VM:

1. Make sure Remote Desktop = Enable (Windows -- Properties)
2. Add RDC to Windows Firewall Exceptions (if Windows Firewall was turn ON)
3. Make sure Windows Users has password (RDC login will not work if the Users password was empty)