Don't work OneConnect OCe10100/OCe10102

V

vicspb

Member
Sep 2, 2023
7
0
6
Greetings.
in server was installed one two-ports ethernet card. I installed a one two-ports network FC card in the server.

at web-interface:
View attachment 88607

lspci show me information:

06:00.0 Ethernet controller: Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) (rev 01)
06:00.1 Ethernet controller: Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) (rev 01)
08:00.0 Ethernet controller: Emulex Corporation OneConnect OCe10100/OCe10102 Series 10 GbE (rev 02)
08:00.1 Ethernet controller: Emulex Corporation OneConnect OCe10100/OCe10102 Series 10 GbE (rev 02)
08:00.2 Fibre Channel: Emulex Corporation OneConnect OCe10100/OCe10102 Series 10 GbE CNA (rev 02)
08:00.3 Fibre Channel: Emulex Corporation OneConnect OCe10100/OCe10102 Series 10 GbE CNA (rev 02)

after install lshw I'm see:


Code: 
        *-pci:1
             description: PCI bridge
             product: 5000 Series Chipset PCI Express x8 Port 4-5
             vendor: Intel Corporation
             physical id: 4
             bus info: pci@0000:00:04.0
             version: b1
             width: 32 bits
             clock: 33MHz
             capabilities: pci pm msi pciexpress normal_decode bus_master cap_list
             configuration: driver=pcieport
             resources: irq:0 memory:d8700000-d88fffff
           *-network:0
                description: Ethernet interface
                product: OneConnect OCe10100/OCe10102 Series 10 GbE
                vendor: Emulex Corporation
                physical id: 0
                bus info: pci@0000:08:00.0
                logical name: enp8s0f0
                version: 02
                serial: 00:00:c9:ea:a3:22
                size: 10Gbit/s
                capacity: 10Gbit/s
                width: 64 bits
                clock: 33MHz
                capabilities: pm msix pciexpress bus_master cap_list rom ethernet physical fibre 1000bt-fd 10000bt-fd
                configuration: autonegotiation=off broadcast=yes driver=be2net driverversion=6.8.12-9-pve duplex=full firmware=4.6.313.21 latency=0 link=yes multicast=yes speed=10Gbit/s
                resources: irq:16 memory:d8800000-d8803fff memory:d8720000-d873ffff memory:d8700000-d871ffff memory:d8880000-d88fffff
           *-network:1
                description: Ethernet interface
                product: OneConnect OCe10100/OCe10102 Series 10 GbE
                vendor: Emulex Corporation
                physical id: 0.1
                bus info: pci@0000:08:00.1
                logical name: enp8s0f1
                version: 02
                serial: 00:00:c9:ea:a3:24
                size: 10Gbit/s
                capacity: 10Gbit/s
                width: 64 bits
                clock: 33MHz
                capabilities: pm msix pciexpress bus_master cap_list rom ethernet physical fibre 1000bt-fd 10000bt-fd
                configuration: autonegotiation=off broadcast=yes driver=be2net driverversion=6.8.12-9-pve duplex=full firmware=4.6.313.21 latency=0 link=yes multicast=yes speed=10Gbit/s
                resources: irq:17 memory:d8804000-d8807fff memory:d8760000-d877ffff memory:d8740000-d875ffff
           *-fiber:0 UNCLAIMED
                description: Fibre Channel
                product: OneConnect OCe10100/OCe10102 Series 10 GbE CNA
                vendor: Emulex Corporation
                physical id: 0.2
                bus info: pci@0000:08:00.2
                version: 02
                width: 64 bits
                clock: 33MHz
                capabilities: pm msix pciexpress cap_list
                configuration: latency=0
                resources: memory:d8808000-d880bfff memory:d87a0000-d87bffff memory:d8780000-d879ffff
           *-fiber:1 UNCLAIMED
                description: Fibre Channel
                product: OneConnect OCe10100/OCe10102 Series 10 GbE CNA
                vendor: Emulex Corporation
                physical id: 0.3
                bus info: pci@0000:08:00.3
                version: 02
                width: 64 bits
                clock: 33MHz
                capabilities: pm msix pciexpress cap_list
                configuration: latency=0
                resources: memory:d880c000-d880ffff memory:d87e0000-d87fffff memory:d87c0000-d87dffff


dmsg:

Code: 
[   15.720428] be2net 0000:08:00.1 enp8s0f1: Link is Up
[   15.747421] vmbr1: port 1(enp8s0f1) entered blocking state
[   15.747426] vmbr1: port 1(enp8s0f1) entered disabled state
[   15.747451] be2net 0000:08:00.1 enp8s0f1: entered allmulticast mode
[   15.747524] be2net 0000:08:00.1 enp8s0f1: entered promiscuous mode
[   15.795416] be2net 0000:08:00.1 enp8s0f1: Link is Up
[   15.795905] 8021q: adding VLAN 0 to HW filter on device enp8s0f1
[   15.800189] vmbr1: port 1(enp8s0f1) entered blocking state
[   15.800203] vmbr1: port 1(enp8s0f1) entered forwarding state
[   15.849063] be2net 0000:08:00.0 enp8s0f0: Link is Up
[   15.876176] vmbr0: port 1(enp8s0f0) entered blocking state
[   15.876180] vmbr0: port 1(enp8s0f0) entered disabled state
[   15.876196] be2net 0000:08:00.0 enp8s0f0: entered allmulticast mode
[   15.876262] be2net 0000:08:00.0 enp8s0f0: entered promiscuous mode
[   15.909412] be2net 0000:08:00.0 enp8s0f0: Link is Up
[   15.909905] 8021q: adding VLAN 0 to HW filter on device enp8s0f0
[   15.913594] vmbr0: port 1(enp8s0f0) entered blocking state
[   15.913609] vmbr0: port 1(enp8s0f0) entered forwarding state
[   17.590770] e1000e 0000:06:00.0 enp6s0f0: NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[   17.590894] e1000e 0000:06:00.0 enp6s0f0: Link Speed was downgraded by SmartSpeed
[  899.339270] vmbr1: port 1(enp8s0f1) entered disabled state
[  899.514131] be2net 0000:08:00.1 enp8s0f1: left allmulticast mode
[  899.514148] be2net 0000:08:00.1 enp8s0f1: left promiscuous mode
[  899.514180] vmbr1: port 1(enp8s0f1) entered disabled state
[  899.521782] be2net 0000:08:00.1: Disabling VLAN promiscuous mode
[  899.608661] vmbr0: port 1(enp8s0f0) entered disabled state
[  899.721568] be2net 0000:08:00.0 enp8s0f0: left allmulticast mode
[  899.721584] be2net 0000:08:00.0 enp8s0f0: left promiscuous mode
[  899.721612] vmbr0: port 1(enp8s0f0) entered disabled state
[  899.729619] be2net 0000:08:00.0: Disabling VLAN promiscuous mode
[ 4064.024533] vmbr0: port 1(enp8s0f0) entered blocking state
[ 4064.024547] vmbr0: port 1(enp8s0f0) entered disabled state
[ 4064.024576] be2net 0000:08:00.0 enp8s0f0: entered allmulticast mode
[ 4064.024663] be2net 0000:08:00.0 enp8s0f0: entered promiscuous mode
[ 4064.049992] vmbr0: port 1(enp8s0f0) entered blocking state
[ 4064.050005] vmbr0: port 1(enp8s0f0) entered forwarding state
[ 4064.319222] vmbr1: port 1(enp8s0f1) entered blocking state
[ 4064.319235] vmbr1: port 1(enp8s0f1) entered disabled state
[ 4064.319265] be2net 0000:08:00.1 enp8s0f1: entered allmulticast mode
[ 4064.319349] be2net 0000:08:00.1 enp8s0f1: entered promiscuous mode
[ 4064.343709] vmbr1: port 1(enp8s0f1) entered blocking state
[ 4064.343723] vmbr1: port 1(enp8s0f1) entered forwarding state



at the same device I'm have two identical devices in the list: fc and eth

but these devices are not working

how can I run them correctly?

thanks
 
You must log in or register to reply here.
Top Bottom