Hey y'all!
I've been following quite a few guides (even reinstalled proxmox at least three times now) and I just can't seem to get this dual port 10GbE HPE 530T to pass through to an OPNSense VM. I've tried vfio, vfio-pci, intel vIOMMU, vfio vIOMMU, and every other thing I found in a post relating to it, but I keep getting the same startup dialogue in OPNSense with no NIC activity:
bxe0: <QLogic NetXtreme II BCM57810 10GbE (BO) BXE v:1.78.91> mem 0x801800000-0x 801ffffff,0x801000000-0×8017fffff, 0x802010000-0×80201ffff irq 16 at device 0.0 o In pci2
bxe0: PCI BARO [10] memory allocated: 0x801800000-0x801ffffff (8388608) -> 0xfff ffe008f800000
bxe0: PCI BAR2 [18] memory allocated: 0x801000000-0×8017fffff (8388608) -> 0xfff
bxe0: PCI BAR4 [20] memory allocated: 0x802010000-0x80201ffff (65536) -> 0xfffff e0085ac8000
bxe0: ERROR: Invalid SHMEM validity signature: 0x00000008
bxe0: ERROR: Invalid phy config in NVRAM (PHY1=0x00000008 PHY2=0x00000008)
bxe0: Unknown media!
bxe0: IFMEDIA flags: 20
bxe0: Using defaults for TSO: 65518/35/2048
(long pause where I screenshot the issue)
bxe0: ERROR: FW failed to respond!
bxe0: MCP response failure, aborting
bxe0: Failed to unload previous driver! time_counter 10 rc -1
(I assume the same for bxe1 but it flies past after the same codes are displayed before the long pause)
All in all, I've even tried disabled SR-IOV in the option rom and disabling the option rom entirely in BIOS. I'm running the latest updates as of today, 2:00pm and I really do not know where to go from here.
I should mention that it works perfectly fine on bare metal, but I can't figure out how to configure a LAGG in proxmox, and I'd rather have the full throughput for opnsense.
I've been following quite a few guides (even reinstalled proxmox at least three times now) and I just can't seem to get this dual port 10GbE HPE 530T to pass through to an OPNSense VM. I've tried vfio, vfio-pci, intel vIOMMU, vfio vIOMMU, and every other thing I found in a post relating to it, but I keep getting the same startup dialogue in OPNSense with no NIC activity:
bxe0: <QLogic NetXtreme II BCM57810 10GbE (BO) BXE v:1.78.91> mem 0x801800000-0x 801ffffff,0x801000000-0×8017fffff, 0x802010000-0×80201ffff irq 16 at device 0.0 o In pci2
bxe0: PCI BARO [10] memory allocated: 0x801800000-0x801ffffff (8388608) -> 0xfff ffe008f800000
bxe0: PCI BAR2 [18] memory allocated: 0x801000000-0×8017fffff (8388608) -> 0xfff
bxe0: PCI BAR4 [20] memory allocated: 0x802010000-0x80201ffff (65536) -> 0xfffff e0085ac8000
bxe0: ERROR: Invalid SHMEM validity signature: 0x00000008
bxe0: ERROR: Invalid phy config in NVRAM (PHY1=0x00000008 PHY2=0x00000008)
bxe0: Unknown media!
bxe0: IFMEDIA flags: 20
bxe0: Using defaults for TSO: 65518/35/2048
(long pause where I screenshot the issue)
bxe0: ERROR: FW failed to respond!
bxe0: MCP response failure, aborting
bxe0: Failed to unload previous driver! time_counter 10 rc -1
(I assume the same for bxe1 but it flies past after the same codes are displayed before the long pause)
All in all, I've even tried disabled SR-IOV in the option rom and disabling the option rom entirely in BIOS. I'm running the latest updates as of today, 2:00pm and I really do not know where to go from here.
I should mention that it works perfectly fine on bare metal, but I can't figure out how to configure a LAGG in proxmox, and I'd rather have the full throughput for opnsense.