Search results

Thank you for this. I was able to install CentOS-Stream-9-latest-x86_64-dvd1.iso by setting CPU Type to host.

You're welcome!

I'm posting this as a guide to help anyone who created FreeNAS/TrueNAS VM on Proxmox Host and need to replace or upgrade a failed Disk. On FreeNAS VM identify the disk that's bad or needs to be replaced Record Disk Name and GUID to be used for getting the Serial Number of the disk Dashboard -->...

You've helped me tremendously with this info. I've also created a freenas VM within Proxmox (Since I started my home lab and haven't changed over to a dedicated TrueNAS server because it just works). Recently I had to make a few drive changes (size increase and failed drive) and I've been...

While trying to make changes to the network config on any of the interfaces I was presented with an error related to bond1 or bond2 iface bond1 - ip address can't be set on interface if bridged in vmbr2 (500) I decided to do the following which resolved the issue: 1. Delete vmbr2 and vmbr3. 2...

I just need to be pointed in the right direction to removing whatever is blocking communication to and from the same subnet on the Primary server.

The Bond config on Primary host vs Secondary host is different because during the Secondary host bond creation when I enter IPv4/CIDR I get an error. When I try remove that config on the Primary host I get and error as well.

Note: I tried accessing accessing the GUI from the same subnet, for the first time since setting everything up and I can't access it. I've never had to access it from the same subnet because my sever is on another floor in my home. However I can access the GUI for the Secondary server from the...

Yes I can ping all the other IP interfaces from the main host: root@dtrinibs:/var/log# ping localhost PING localhost.localdomain (127.0.0.1) 56(84) bytes of data. 64 bytes from localhost.localdomain (127.0.0.1): icmp_seq=1 ttl=64 time=0.033 ms 64 bytes from localhost.localdomain (127.0.0.1)...

I'm guessing this is a unique case and not very common.

Hi nktech1135, 1. I just checked the firewall on the Primary server and I found one entry (unknown to me but not surprised because I installed the Nagios agent on that server). root@dtrinibs:~# pve-firewall status Status: disabled/running 2. The secondary server's...

Hi, I'm trying to set up a cluster with two servers that are on the same subnet with no luck. Firewall isn't enabled on any of the servers. I've checked my internal firewall and confirmed none of the traffic is being blocked by router. I need to remove the block to my Primary server that only...

I'm on 6.1-7 and I can see the Features nesting option under the Container. Can you send a screenshot of the Options section for your container? If you don't see it in 6.1-8 you might want to try updating the config using my previous method...

Yes I saw that option but like you mentioned no disk were available in the drop down. So I decided to do to it the way I used above, but didn't think to only wipe the disk and try again.

Hi, This was really helpful. I added a Marvell 88SE9230 PCIe SATA 6Gb/s Controller to my server to extend my current storage. I have my main proxmox install on a 500GB SSD which after a few VMs, CTs and backups ran low on space. So I added that controller so I can have a dedicated storage...

Hi Janssensm, Your reply helped me a lot got me on the right track. I bought IOCrest SI-PEX50102 M.2 Plus SATA to PCI-E x2 Hardware Raid Card Vendor: Marvell Technology Device: 88SE9230 PCIe SATA 6Gb/s Controller With two 1TB M.2 Cards and a 3TB HDD via SATA cable installed on to the card...

Update Nov 1st 2018: During my monthly server maintenance, I ran into this error again and found a similar solution. Instead of adding the below and entry into each lxc container to allow NFS mounting due to apparmor security: /etc/pve/lxc/<lxcname>.conf lxc.apparmor.profile...

Hi Karnz, That worked. I added the configuration to all my lxc's that needs it restarted the container to the config can be loaded and my nfs mounts are now mounted. Many thanks to you! Dwain

Hi Karnz, I'm trying to follow what you did but I don't get it. You said to add profile "lxc.apparmor.profile: lxc-container-default-cgns" to each LXC ID config file. Do you mean to go to /var/lib/lxc/<conatiner number> container and edit the config file by adding this to the end of the...