Search results

Thanks @leesteken . Some time ago I replaced /dev/sdb on same server. This time it should be /dev/sda drive, so that's why I'm worried. Let's say aaa is good drive, bbb is bad drive and ccc is the new drive Last time I did this: #save a backup and loaded on new disk sgdisk --backup=table...

Hello. I was tasked to do a disk replacement on a very, very, very old Proxmox installation. # pveversion pve-manager/4.3-1/e7cdc165 (running kernel: 4.4.19-1-pve) The server was installed on ZFS raid 1 Array (mirror). Before continuing let me say I was told: This server WONT be upgraded. I...

You can config samba to use IPv4 only. interfaces = your.ipv4.network.address bind interfaces only = Yes But if you insist in disabling IPv6 at SO level I think you could edit /etc/sysctl.conf (not tried yet) $ sudo nano /etc/sysctl.conf # add these lines at bottom...

Thanks @matrix. Do you mean content of /etc/network/interfaces ? auto lo iface lo inet loopback iface eno1 inet manual auto vmbr0 iface vmbr0 inet static address 192.168.0.250/24 gateway 192.168.0.1 bridge-ports eno1 bridge-stp off bridge-fd 0

Hi, I have a really simple setup. CableModem/Router/AP | Switch TL-SG1024 |-----Proxmox |-----Raspberry Pi4 (x6) |-----Printer HP (x2) Proxmox is fully updated # pveversion -v proxmox-ve: 6.2-1 (running kernel: 5.4.34-1-pve) pve-manager: 6.2-4 (running version...

Thanks Lnxbil & alexskysilk. This server will not have any database. ERP they use is just a frontend client that connects to a middleware that interacts with database. I was concerned about having 50 RDS users on virtualized WS2016 on that hardware. Also 48GB ram seems too little for 50 users...

Hello, To put some background: I live in Argentina. Our economy is a mess; smal companies can't (or don't want to) afford enterprise grade hardware. So mainly buy budget hardware or (even worst) consumer grade desktop machines AS SERVERS!!! And then they expect that shitty hardware give...

Thank you wolfgang! I should backup and reinstall then. ;)

I can't figure out how it works... I need to read A LOT more about LVM. I made this test on a VM: installed proxmox as default on a 16GB disk. So root was 7GB. I ran then: # lvresize -L+3G pve/root # touch /forcefsck && reboot ... then ... # resize2fs /dev/pve/root and / grew up to 10GB. Is...

Hi, I installed Proxmox 4.2 on a PC. As I have 1 disk, I choosed ext4 on install options. I found that 1TB disk was partitioned Device Start End Sectors Size Type /dev/sda1 34 2047 2014 1007K BIOS boot /dev/sda2 2048 262143 260096 127M EFI System...

Hi to all. I need guidance/advice. I have a single Proxmox 3.2 server running 2 openvz and 3 KMV. I'm planning to do a clean install of version 4.2 All I have to do is convert openvz to lxc and backup to external drive, right? Then, restoring those backups should run without issues. (saving...

Thanks fabian for the explanation. I really didn't know that. I really worried there were a security issue or something. Thanks again

I'm really not sure about where to report this. I know this is not a Proxmox bug, so I'm asking for guidance (and also to inform this to you). I have a Proxmox server at home. I made a container and installed Gnome, Xdummy and x11vnc to have a full desktop. So I can access this containerized...

Thanks LnxBil & linkstat I just leave containers alone... :)

Hi, I have some strange issue with containers. systemd is not running on containers after proxmox reboots. This is my setup: # uname -a Linux proxmox 4.4.13-2-pve #1 SMP Fri Jul 15 06:36:47 CEST 2016 x86_64 GNU/Linux # pveversion --verbose proxmox-ve: 4.2-58 (running kernel: 4.4.13-2-pve)...

Hi, I have a proxmox server. It's a really small implementation, for my personal use, at my home. # pveversion -v proxmox-ve-2.6.32: 3.3-139 (running kernel: 2.6.32-33-pve) pve-manager: 3.3-5 (running version: 3.3-5/bfebec03) pve-kernel-2.6.32-33-pve: 2.6.32-138 pve-kernel-2.6.32-29-pve...

Hi. I have proxmox on a Gigabyte Z87X-D3H + Core i7-4770 + 16GB ram # pveversion -v proxmox-ve-2.6.32: 3.3-138 (running kernel: 2.6.32-33-pve) pve-manager: 3.3-2 (running version: 3.3-2/995e687e) pve-kernel-2.6.32-33-pve: 2.6.32-138 lvm2: 2.02.98-pve4 clvm: 2.02.98-pve4 corosync-pve: 1.4.7-1...

Thanks bankir382. I'm pretty sure it works. Will try at first chance. At this time that VM is in use.

Hi, I have a single proxmox node with 1 CT and 3 VMs # pveversion -v proxmox-ve-2.6.32: 3.2-121 (running kernel: 2.6.32-27-pve) pve-manager: 3.2-1 (running version: 3.2-1/1933730b) pve-kernel-2.6.32-27-pve: 2.6.32-121 lvm2: 2.02.98-pve4 clvm: 2.02.98-pve4 corosync-pve: 1.4.5-1 openais-pve...

I was using vncterm because easy-to-use, just log in and pull the java app. For spice it's ok on windows but debian has not updated packages, on Arch spice don't show cursor... oh well. It was less painfull to use vncterm. Will try spice again Enviado desde mi GT-I8190L mediante Tapatalk