Search results

Just wanted to say THANKS! This is my exact situation and I am not super technical so this guide was REALLY helpful :)

I have created a storage called "removable" which was just a USB drive, but I cannot remember which USB port I had it plugged into originally on my server. At the moment, the storage is shown as (?) because it probably isn't mounted correctly: What steps do I need to take to remount it...

I ended up passing it through without converting as no one could assist. It works but is showing up as "Usage: partitions" while the other drives are showing up as "Usage: ZFS". Hope this doesn't cause any errors.

This is a long winded tale, but in short: Originally had 4x HDD passing through to my VM 101 and each was a ZFS. The VM was TrueNAS and I handled a RAID pool within the VM. One of the HDD became faulty (/dev/sda) so I replaced with a new hard drive (originally /dev/sdf). However, I think I...

OMG so I finally was able to recover GUI by turning off autoboot for the VM very quickly before it started to corrupt, now I just need to figure out how to get it working again! qm set 101 ---autostart 0

Could this have been linked and caused by this: https://forum.proxmox.com/threads/i-o-errors-pve-not-booting.75120/post-343494

I am getting a lot of Buffer I/O error on device dm-1, logical block

For both I am getting -bash: /use/sbin/qm: Input/output error

I have no idea what caused it but something is stopping me from loading GUI since thing to pass it through. Maybe the same controller that I the OS runs on? I tried your command and got: "unable to open file '/etc/pve/nodes/proxmox/qemu-server/101.conf.tmp.2536' - Input/output error"

Need help. I'm still a bit of a noob. Have Procmox set up with two VM's. Tried to pass through PCI to one of the VM's and now on reboot I can't access Web GUI. Is there a way to remove that hardware option via command line? I think I need to remove the "hostpci0: 00:17" from my qm config 101

Apologies, I thought I had to run the command lines one after the other (qm set followed by update). Again, thank you for the super prompt response and all your assistance!

Thanks for the prompt response! Trying disk passthrough at the moment, thanks for linking the Wiki! Stuck on the following line: update VM 101: -scsi2 /dev/disk/by-id/ata-WDC_WDXXXYYYYY So then I try apt: apt update VM 101: -scsi2 /dev/disk/by-id/ata-WDC_WDXXXYYYYY Any tips?

Thanks for the help! Here is the output: IOMMU group 0 00:00.0 Host bridge [0600]: Intel Corporation Skylake Host Bridge/DRAM Registers [8086:1918] (rev 07) IOMMU group 10 04:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03) IOMMU group 1...

So I am trying to get FreeNAS working and pass through my 4x internal HDD's to the VM so that I can run a pool within the VM. At first, I was getting the following error: After following the Wiki, I ensured that the BIOS had Virtualization enabled and also made sure that remapping was enabled...

Thanks! Your dpkg line taught me something new, and rather than ask how to remove it I used --help to find out that -P urge should work, and fairly certain it did. I also tried dabbling in installing samba to get my ZFS storage accessible on my windows PC, but kept getting login errors and just...

Thanks for the help Dominic! Much appreciated :) Does this mean I should delete/remove it and run it in a container and if so how do I do that if I can't find it)? I wouldn't know how to remove it as I didn't specifiy a container so I assume it is running on the Node? Are there any downsides to...

Hi All, Very new to Proxmox, but have it up and running now and have been hosting a Home Assistant container via an LXC container using a 1 line command install, which has been working wonderfully! Now, I want to delve into the secondary purpose of my home server, but have no experience so...

OF COURSE! Shows you why I dropped out of my IT Networking subjects at uni. That worked, thank you SO SO much Dunuin!!!!!

Nope, IP Router is 192.168.1.1, I actually made sure that the IP address was used previously by a different device before assigning it. It is not currently in use so it should be okay. Not really sure what you mean about nameserver, here are my DNS settings in ProxMox: Search Domain: local DNS...

Hi All, Really struggling, everyone else's youtube tutorials seem to be able to automatically connect to the internet without furhter setting up or changing values for networking, but mine won't even show up in my router(DSL-5300) in the list of connected devices, but I can access the GUI still...